产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
模温控制与模具热平衡 功率核算与常见偏差 Mold Temperature Control and Heat Balance
一、模温机真正管的是什么 | What a Temperature Controller Really Controls

模温机不是"把水烧热"的机器,它管的是模具型腔的温度稳定。注塑周期里,熔料带进来的热量、冷却水带走的热量、模腔表面对空气的散热同时发生,模温机的作用是让这三者在一个周期内收支平衡,让每一模的模温落在同一个窄带内。
A temperature controller is not a water heater; it holds the mould cavity temperature stable. Inside one cycle, heat from the melt, heat removed by cooling water and heat lost from the cavity surface all act at once. The unit balances this budget so that every shot starts from the same narrow temperature band.
二、三类机型怎么分 | Three Types and Where They Fit
水温机:以水为介质,控温上限约 90~120℃,升温快、成本低,适合一般注塑与挤出模具,也是模具冷却与升温两用机型。
Water units use water as medium, reaching roughly 90–120 °C, heat up fast and cost less; they suit ordinary injection and extrusion moulds and cover both heating and cooling duty.
油温机:以导热油为介质,控温上限可达 200℃ 以上,温度稳定、不结垢,适合高温工程塑料、压铸与辊筒控温。
Oil units use heat transfer oil, reaching above 200 °C with stable temperature and no scaling; suited to high-temperature engineering resins, die casting and roll temperature control.
水油两用机:同一台机器可切水或切油,适合工艺跨度大、机型不固定的车间,代价是换热效率按水侧设计,油工况下升温稍慢。
Dual-medium units run water or oil on the same frame, useful where processes vary; the trade-off is that the heat exchanger is sized for water, so oil heating is slower.
三、功率怎么算 | How to Size the Heater
升温功率按"模具质量 × 比热 × 温升 ÷ 目标升温时间"估算,再乘 1.2 的余量。举例:一套 800 kg 的模具,钢的比热约 0.46 kJ/(kg·K),从 25℃ 升到 80℃,温升 55 K,需热量约 20 200 kJ;若要求 30 分钟升到位,则功率不低于 11 kW,取 12~15 kW 机型。
Heating power is estimated as mould mass × specific heat × temperature rise ÷ target heat-up time, plus a 20% margin. Example: an 800 kg mould, steel specific heat about 0.46 kJ/(kg·K), from 25 °C to 80 °C — a 55 K rise needs about 20 200 kJ; for a 30-minute heat-up the heater must exceed 11 kW, so choose 12–15 kW.
冷却能力则按"每周期需带走的热量 ÷ 温差"折算流量:注塑件每公斤约需带走 300~400 kJ 的热量,单周期 2 kg 制品、周期 30 秒,则每小时需带走约 72 000~96 000 kJ,配 5~7℃ 温差计算,循环流量在 40~60 L/min 量级。
Cooling capacity follows the heat to be removed per cycle divided by the allowable temperature difference: a kilo of moulded part carries away roughly 300–400 kJ; two kilos per 30-second cycle means 72 000–96 000 kJ per hour, which at a 5–7 K difference works out to about 40–60 L/min of circulating flow.
四、接口与管路 | Connections and Piping
模具水道要按"先并联后串联"的原则布置,避免一路阻力大、一路没流量;进出水口加装温度探头与压力表,温差超过设定值时先查流量而不是先加功率。
Mould cooling channels should be balanced in parallel rather than daisy-chained, otherwise one branch starves. Fit temperature probes and pressure gauges at inlet and outlet; when the difference exceeds the setpoint, check flow before adding power.
管路要做保温,尤其是油温机的回流管;管径按流量与流速选,水流速控制在 1.5~2.5 m/s,过低易积气、过高磨损与噪声都上来。
Insulate the piping, especially the oil return line; size it by flow and velocity, keeping water velocity around 1.5–2.5 m/s — too low traps air, too high brings wear and noise.
五、现场常见的四种偏差 | Four Typical Deviations
一模冷一模热:多为冷却水路不平衡或模温机流量不足,先测各支路回水温差。升温慢:加热功率不足、导热油劣化或换热器结垢。温度波动大:探头位置不当(贴壁或悬空),或水箱容积过小导致回水温度被瞬间拉低。频繁高压报警:管路堵塞或水泵选大。
Shot-to-shot variation points to unbalanced cooling branches or low flow — measure return temperatures per branch. Slow heat-up means undersized heater, degraded oil or scaled exchanger. Wide fluctuation comes from a badly placed probe or an undersized tank. Repeated high-pressure alarms mean a restriction or an oversized pump.
六、和冷水机、干燥机怎么配合 | Working with Chillers and Dryers
模温机负责"稳",冷水机负责"降",两者不要互相顶:模具需要快速降温时用冷水机供冷水,模温机切到冷却模式做回路缓冲;干燥机管的是料,模温机管的是模,两条线各自独立计量,才能定位问题出在料还是模。
The temperature unit stabilises, the chiller removes heat; they must not fight each other. For fast cooling, feed chilled water and let the unit act as a buffer; the dryer governs resin, the unit governs the mould, and keeping the two metered separately is what makes diagnosis possible.
七、延伸阅读 | Further Reading
高温模温机功率核算见 高温模温机选型与功率核算;模温机与注塑机匹配见 模温机配注塑机选型号方法;压铸高温工况见 压铸高温模温机;整线配套思路见 中央供料系统从选型到落地。
For power calculation see the high-temperature unit article; for matching a unit to an injection machine see the model selection note; for die casting duty see the high-temperature die casting article; for the complete line configuration see the central feeding pillar.
