产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
郑州冷水机 TCL-10HP 风冷箱式|注塑模具降温
郑州冷水机 TCL-10HP
Industrial Chiller TCL-10HP for Zhengzhou
郑州冷水机 TCL-10HP(Industrial Chiller TCL-10HP):风冷箱式一体机,出水温度 7~15℃,面向中原及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。
Industrial Chiller TCL-10HP for Zhengzhou: an air-cooled unit with outlet water at 7-15 C, supplied to central China and nearby cities, with cooling-load sizing, piping advice, delivery and on-site commissioning.
设备说明 / Equipment Overview
10HP 风冷箱式,单机可带 1~2 台中型注塑机,机身带脚轮可移位;电控预留通讯口,便于把水温与报警接到中控。
A 10HP air-cooled box unit serving one or two mid-size presses, on castors so it can be moved. A communication port lets water temperature and alarms reach the central control.
结构与控制 / Structure & Control
冷媒侧用翅片冷凝器加轴流风机,水侧为不锈钢水箱配管道泵,控制板把温度、压力、电流集中显示在一屏;接线端子做编号标识,便于现场按图排查。
The refrigerant side uses finned coils with axial fans, the water side a stainless tank with an inline pump, and one board displays temperature, pressure and current together. Terminals are numbered so faults can be traced against the diagram on site.
运行与精度 / Performance & Accuracy
中部夏季高温时段长,风冷机在 38℃ 以上环境冷量衰减更快,按较高环境温度校核冷凝压力;车间闷热时把机组移到室外或加导风罩,比单纯加大匹数更省电。
Summers here stay hot for long stretches and air-cooled capacity fades faster above 38 C, so condensing pressure is checked at peak ambient. Moving the unit outdoors or adding a duct hood saves more power than simply buying extra horsepower.
操作与维护 / Operation & Maintenance
旺季前统一做一次保养:清翅片、换滤网、校探头、紧端子;运行期间每周看一次电流与压力表读数,数值比平常高说明冷凝侧脏或冷媒偏少,先排查再补冷媒。
Do one full service before peak season: clean fins, change filters, verify probes, tighten terminals. During running, check current and gauge readings weekly; values above normal mean a dirty condenser or low charge, so investigate before adding refrigerant.
参数速览 / Specifications
型号 TCL-10HP|制冷量 约 9 kW|出水温度 7~15℃|控制精度 ±1℃|循环流量 约 30 L/min|水泵压力 0.15~0.2 MPa
Model TCL-10HP | Capacity approx. 9 kW | Outlet 7-15 C | Control accuracy plus or minus 1 C | Flow approx. 30 L/min | Pump pressure 0.15-0.2 MPa
应用场景 / Applications
包装瓶盖与容器模具、PVC 与 PE 管材定型、注塑日用品与农用件生产、挤出造粒后的水环切粒冷却。
Bottle cap and container molds, PVC and PE pipe calibration, daily-goods and agricultural parts, and water-ring pelletising cooling after extrusion.
中原地区配套 / Local Supply in central China
郑州及中原地区以包装容器、管材、注塑日用品与农用塑料为主,机台以中小吨位居多,订单季节性强、旺季开机时间长。当地物流辐射面广,对发货时效与备件供应看得重,也希望机组结构简单、现场电工能自行处理常规故障。
Zhengzhou and central China focus on packaging containers, pipe, daily-goods and agricultural molding, mostly small and medium tonnage with seasonal orders and long peak running hours. Logistics reach is wide, so delivery timing and spare availability matter, and the unit should stay simple enough for a plant electrician to handle routine faults.
选型与交付流程 / Sizing & Delivery
按旺季很长开机时段估算冷量,给出移机与固定两种安装建议;到场调试后留一份常见故障对照表,交班人员可先按表排查再去电话找工程师。
We size on the longest peak-season running block and quote both movable and fixed layouts. After commissioning a fault lookup table stays on site, so shift crews can check it before calling an engineer.
常见问题 / FAQ
Q:一台能带几台注塑机?
Q: How many machines can one chiller serve?
A:按同时开机的总冷量算,5HP 一般带 1 台 100 吨级或两副小模,10HP 带 1~2 台中型机,20HP 带 3~6 副模具;换模频繁的车间按同时使用率折算,别按机台铭牌直接累加。
Size on simultaneous load: 5HP covers one 100 t machine or two small molds, 10HP one to two mid-size machines, 20HP three to six molds. In job shops with frequent mold changes, use a simultaneity factor instead of adding nameplates.
Q:水质不好会不会结垢?
Q: Will poor water quality scale the unit?
A:会,水侧硬度高时蒸发器与冷凝器都容易挂垢,换热效率逐月下降;加装软化装置或用去离子水,按季度清洗,注水前先冲洗管路,别把施工碎屑带进机组。
Yes. Hard water scales both evaporator and condenser and efficiency falls month by month. Fit a softener or use de-ionised water, clean quarterly, and flush the piping before filling so construction debris stays out.
相关产品与内容 / Related Products
郑州 本地配套与选型提示 / Local Notes for 郑州
包装、管材与日用品为主,人工上料比例高,料斗要加料位报警,避免空斗导致配比失真。
Local industry sets the material mix in 郑州, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:壳管式冷水机。
Model and configuration: 壳管式冷水机.
