产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

苏州冷水机 TCL-5HP 风冷小机|精密件控温

日期:2026-11-20 22:47
浏览次数:23
摘要:苏州冷水机 TCL-5HP Industrial Chiller TCL-5HP for Suzhou 苏州冷水机 TCL-5HP(Industrial Chiller TCL-5HP):风冷小机一体机,出水温度 8~12℃,面向苏南及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。 Ind

苏州冷水机 TCL-5HP 整机 纯白底图

苏州冷水机 TCL-5HP
Industrial Chiller TCL-5HP for Suzhou

苏州冷水机 TCL-5HP(Industrial Chiller TCL-5HP):风冷小机一体机,出水温度 8~12℃,面向苏南及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。
Industrial Chiller TCL-5HP for Suzhou: an air-cooled unit with outlet water at 8-12 C, supplied to southern Jiangsu and nearby cities, with cooling-load sizing, piping advice, delivery and on-site commissioning.

设备说明 / Equipment Overview

5HP 风冷小机型,适合一机一机台或一拖二的精密注塑位;机身窄,可直接摆在机台侧面,进出水用快速接头,换模时不必拆管。
A compact 5HP air-cooled unit for one press, or two small presses at most, on precision work. Its narrow frame sits beside the machine, quick couplings handle supply and return, and mold changes need no pipe work.

结构与控制 / Structure & Control

钣金箱体一体化,压缩机加隔声罩,翅片冷凝器前置,电控板防水防尘;水箱容量按 15 分钟循环量配,配自动补水与溢流口,水泵为管道式,进出口各带一块压力表。
An integrated sheet-metal body houses a silenced compressor with the finned condenser at the front and a sealed control board. Tank volume covers about 15 minutes of circulation, with automatic make-up and overflow; the inline pump carries a gauge on each side.

运行与精度 / Performance & Accuracy

支持定点控温与固定温差两种模式,定点模式适合光学件与医疗件;压缩机设很小运行时间与很短停机时间,避免小负荷频繁启停导致水温锯齿波动。
Two control modes are offered: fixed set point, which suits optical and medical parts, and fixed difference. The compressor has minimum run and minimum off times, so a light load does not produce saw-tooth temperature swings.

操作与维护 / Operation & Maintenance

每两周清理一次进风滤网,翅片用低压气吹扫;精密件车间水侧建议用去离子水或软化水,减少结垢与杂质;每半年检查快接接头密封圈,渗漏会直接拉低流量。
Clean the intake filter every two weeks and blow the fins with low-pressure air. For precision work use de-ionised or softened water to limit scale and particles, and check quick-coupling seals every six months since leakage directly cuts flow.

参数速览 / Specifications

型号 TCL-5HP|制冷量 约 4.5 kW|出水温度 8~12℃|控制精度 ±1℃|循环流量 约 15 L/min|水泵压力 0.15 MPa
Model TCL-5HP | Capacity approx. 4.5 kW | Outlet 8-12 C | Control accuracy plus or minus 1 C | Flow approx. 15 L/min | Pump pressure 0.15 MPa

应用场景 / Applications

精密注塑模温控制、光学与医疗件成型、小型激光与检测设备冷却、实验室恒温循环。
Mold temperature control on precision molding, optical and medical part production, cooling for small laser and inspection equipment, and constant-temperature loops in laboratories.

苏南地区配套 / Local Supply in southern Jiangsu

苏州一带以精密注塑、连接器、光学件与医疗耗材为主,单件小、公差紧,对水温稳定与洁净度要求高于产量。车间多恒温、机台排布紧凑,倾向小冷量机组就近布置、一机一回路,还希望噪音低、能并入车间能源看板。
Suzhou specialises in precision molding, connectors, optical parts and medical consumables, where small parts and tight tolerances put water stability and cleanliness ahead of output. Shops are climate-controlled and tightly packed, so small units sit next to the press on one loop each, with low noise and a tie-in to the plant energy dashboard.

选型与交付流程 / Sizing & Delivery

按单件重量与周期测算单模冷量,再按回路数量配管径;到场先做 24 小时空载水温记录,确认波动在 ±1℃ 内再接入模具,避免一开始就带满负荷掩盖问题。
We size the per-mold load from part weight and cycle time, then set pipe diameter by loop count. On site a 24-hour no-load temperature log is taken first; production starts only once the swing is within plus or minus 1 C, so problems are not masked by full load.

常见问题 / FAQ

Q:一台能带几台注塑机?
Q: How many machines can one chiller serve?
A:按同时开机的总冷量算,5HP 一般带 1 台 100 吨级或两副小模,10HP 带 1~2 台中型机,20HP 带 3~6 副模具;换模频繁的车间按同时使用率折算,别按机台铭牌直接累加。
Size on simultaneous load: 5HP covers one 100 t machine or two small molds, 10HP one to two mid-size machines, 20HP three to six molds. In job shops with frequent mold changes, use a simultaneity factor instead of adding nameplates.

Q:水质不好会不会结垢?
Q: Will poor water quality scale the unit?
A:会,水侧硬度高时蒸发器与冷凝器都容易挂垢,换热效率逐月下降;加装软化装置或用去离子水,按季度清洗,注水前先冲洗管路,别把施工碎屑带进机组。
Yes. Hard water scales both evaporator and condenser and efficiency falls month by month. Fit a softener or use de-ionised water, clean quarterly, and flush the piping before filling so construction debris stays out.

相关产品与内容 / Related Products

苏州 本地配套与选型提示 / Local Notes for 苏州

电子、医疗与精密注塑集中,洁净与静电要求高,洁净车间要控粉尘,建议混料腔密闭并留除尘接口,换料用负压清扫。
Local industry sets the material mix in 苏州, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:壳管式冷水机。
Model and configuration: 壳管式冷水机.

相关阅读 / Related Reading

粤公网安备 44190002002288号