产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

称重混料与多组份配比 精度、节拍与配方切换 Gravimetric Blending Accuracy Cycle Time and Recipe Change

日期:2026-11-20 21:18
浏览次数:38
摘要:一、为什么配比会失准 | Why Ratio Drifts 多组份混料失控,多数不是机器坏了,而是三种误差叠加:计量误差(每一次称多少)、时序误差(什么时候称)、残留误差(上一批料还剩多少)。容积式配比只看体积,色母粒的堆密度一批一个样,误差会集中在色差上;称重式把每一组份单独称出来,误差落在配方比

一、为什么配比会失准 | Why Ratio Drifts

称重式混料机 Gravimetric Blender

多组份混料失控,多数不是机器坏了,而是三种误差叠加:计量误差(每一次称多少)、时序误差(什么时候称)、残留误差(上一批料还剩多少)。容积式配比只看体积,色母粒的堆密度一批一个样,误差会集中在色差上;称重式把每一组份单独称出来,误差落在配方比例上,可测、可纠。

Unstable blending usually comes from three stacked errors: metering error (how much per shot), timing error (when it is metered) and carry-over error (what is left from the previous batch). Volumetric dosing measures volume only, so colour masterbatch bulk density varies batch to batch and the error shows up as colour deviation; gravimetric dosing weighs each component, so the error lands on the recipe ratio and can be measured and corrected.

二、三种配比方式的适用边界 | Where Each Dosing Method Fits

容积式(色母机、转盘式):结构简单、价格低、响应快,适合比例固定、色差要求不严的场合,一般用在单色或双色小比例添加。

Volumetric (masterbatch units, disc type): simple, lower cost, fast response; suitable when the ratio is fixed and colour tolerance is loose, typically small-ratio single or dual colour additions.

称重式(增重式混料机):各组份按设定重量依次计量后落入混料桶,精度取决于称重传感器与落差补偿,适合 2~6 组份、比例经常调整的场合。

Gravimetric batch blending: each component is weighed in turn and dropped into the mixing chamber; accuracy depends on the load cell and the drop compensation. Suits 2–6 components with frequently changed recipes.

失重式(连续计量喂料):螺杆连续出料,按单位时间失重速率闭环控制,适合挤出、片材、流延等连续生产线,以及粉料、破碎料等难流动的物料。

Loss-in-weight: the screw feeds continuously and the weight-loss rate is closed-loop controlled; suited to extrusion, sheet and cast film lines and to powders or regrind that flow poorly.

三、精度怎么算、怎么验收 | Accuracy: Calculation and Acceptance

单次称量误差通常按传感器量程的百分比给出,但现场真正要盯的是「批内极差」:连续取 10 批,记录每批的实际配比,看极差是否落在工艺允许带内。换算成品色差时,色母比例 1% 的配方,0.1% 的比例漂移就是 10% 的相对变化,所以小比例配方要用小量程传感器,而不是大量程凑精度。

Per-shot accuracy is usually quoted as a percentage of load-cell range, but what matters on site is the spread within a batch: take ten consecutive batches, record the actual ratio, and check the spread against the process band. For a 1% masterbatch recipe, a 0.1% drift is a 10% relative change, so small-ratio recipes need a small-range load cell rather than a wide-range one.

节拍要一起算。称重是串行的,组份越多、单次称量越小,循环时间越长;如果成型周期短、用料快,就要用双称斗或预称料仓把计量与放料并行,否则配比准了、节拍跟不上。

Cycle time must be calculated together with accuracy. Weighing is serial — more components and smaller shots mean longer cycles. With short molding cycles, use dual weigh hoppers or a pre-weigh bin to overlap metering and discharge.

四、换料与清洗 | Material Changeover and Cleaning

换色、换料时,残留是主要污染源。混料桶、下料管、称斗都要能拆、能吹;小比例组份的称斗建议单独做小容积,减少挂料面。换料程序写进控制器的配方键,一键调用清洗吹扫,比靠人记忆可靠。

On colour or material change, residue is the main contamination source. Mixing chamber, discharge pipes and weigh hoppers should be removable and purgeable; keep the small-component hopper small to cut hanging area. Store changeover routines as recipe keys with one-key purge, which is more reliable than relying on memory.

五、常见问题对照 | Common Symptoms and Causes

色差忽深忽浅——先查色母计量是否受回料粒形影响,再查混料时间是否够;配比整体偏高或偏低——查落差补偿参数与称斗零点;混料不均——查搅拌时间与桶内是否积料;报警频繁——查料位与吸料节拍是否匹配。

Colour swinging: check whether metering is affected by regrind shape, then check mixing time. Ratio drifting high or low: check drop compensation and hopper zero. Poor dispersion: check mixing time and build-up in the chamber. Frequent alarms: check level signals against the loading cycle.

六、延伸阅读 | Further Reading

注塑称重混料机的工作原理见 注塑称重混料机的称重原理是什么;控制系统构成见 注塑称重混料机的控制系统一般由哪些部分组成;多种料称重计量见 多种料称重计量混合机;自动配料见 自动混料配料系统;挤出与流延配比见 挤出称重配料系统 与 流延机称重计量比例称重系统;六组份配比见 密炼机6组分称重配料;四组份拉片见 拉片机称重混料机 4组分比例配料;配方与喂料的分工见 色母机、失重式喂料机、称重式混料机分工;工艺参数全书见 结晶与除湿干燥工艺参数全书。

See the linked notes on gravimetric blender working principle, control architecture, multi-component weighing, automatic batching, extrusion and cast film dosing, six-component and four-component recipes; for the division of labour between masterbatch units, LIW feeders and gravimetric blenders see the dedicated article.

相关阅读 / Related Reading

称重式混料机

粤公网安备 44190002002288号