产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

中央供料系统从选型到落地:五层结构、参数算法与故障排查 Central Feeding System Guide

日期:2026-11-21 00:59
浏览次数:53
摘要:一、五层结构,先认清楚再谈选型 中文: 中央供料系统 由五层组成:储料站(原料集中存放与破拱)、干燥站(除湿干燥与料温控制)、分配站(一拖多切换阀与清管)、输送管路(负压输送与过滤)、控制层(PLC 与配方管理)。 English: A central feeding system has five

一、五层结构,先认清楚再谈选型

失重秤喂料机 Loss-in-Weight Feeder

中文:中央供料系统由五层组成:储料站(原料集中存放与破拱)、干燥站(除湿干燥与料温控制)、分配站(一拖多切换阀与清管)、输送管路(负压输送与过滤)、控制层(PLC 与配方管理)。

English: A central feeding system has five layers: material storage (bulk holding and arch-breaking), a drying station (dehumidified drying and temperature control), a distribution station (one-to-many valves and line clearing), the conveying pipeline (vacuum transfer and filtration), and the control layer (PLC and recipe management).

中文:这五层里任何一层掉链子,车间感受到的现象都一样:机台等料。所以排查要按层往下走,不要一上来就拆吸料机。

English: If any of these layers underperforms, the shop floor symptom is identical: machines waiting for material. Diagnose layer by layer instead of pulling the loader apart first.

二、参数按机台算,不按经验估

中文:先用三组数把规模定下来:机台数量、单机小时耗量、换料频次。

English: Fix the scale with three numbers first: machine count, hourly consumption per machine and changeover frequency.

中文:风量:按同时在吸的机台数叠加单机需求,再留 15%~20% 余量。风机长期满负荷运行,滤芯压损一抬头就带不动了。

English: Airflow: sum the demand of concurrently loading machines and add 15–20 % margin. A fan running flat out loses capacity as soon as filter pressure loss rises.

中文:管径:颗粒输送的气流速度取 18~25 m/s,管径由总风量与流速反算,弯头处适当放大一档。

English: Pipe diameter: keep conveying velocity at 18–25 m/s for pellets and size the pipe from total airflow and velocity, going one size up at bends.

中文:真空度:颗粒常规取 -25~-40 kPa 量级;粉体要更高真空并加脉冲清灰。

English: Vacuum level: roughly -25 to -40 kPa for pellets; powders need a higher vacuum plus pulse-jet cleaning.

中文:储料容量:按一个班次到 24~36 小时的用量配容积。太小频繁补料,太大则料在仓内吸潮。

English: Storage capacity: size the silo for one shift up to 24–36 hours of consumption. Too small means constant refilling; too large means moisture pickup inside the silo.

三、管路设计的三条硬规则

中文:规则一:一条主管服务的机台不超过 12 台,超过就拆成两条主管,否则末端真空度撑不住。

English: Rule one: keep one main line to no more than 12 machines; split it into two beyond that, or end-of-line vacuum collapses.

中文:规则二:弯头用大半径,避开急弯。每个弯头都在消耗压力,弯头越多,末端吸力越弱。

English: Rule two: use long-radius bends and avoid sharp elbows. Every bend consumes pressure, so more bends mean weaker suction at the end.

中文:规则三:不同牌号共用管路必须配清管程序。清管不到位,串色串料就是常态。

English: Rule three: grades sharing a line must have a line-clearing routine. Without it, color and material cross-contamination is routine.

四、控制层管三件事

中文:哪台机用哪种料、什么时候补、补多少,这三件事都在控制层。

English: Which material each machine uses, when to refill and how much are all handled by the control layer.

中文:分配阀按配方呼叫料源,料位传感器触发补料,PLC 记录每次输送的料号、机台与时间,错料时能倒查。

English: Distribution valves call the source by recipe, level sensors trigger refills, and the PLC logs the material, machine and time of every transfer so mis-feeding can be traced.

中文:每台机建议设独立的高低料位双点触发,比单点稳,能减少频繁启停与空吸。

English: Give each machine separate high and low level setpoints; two-point triggering is steadier than one point and reduces frequent start-stop and dry running.

五、故障排查顺序

中文:吸料不畅:先查滤芯压损,再查料管打折,再看吸料嘴是否埋在料里。

English: Poor loading: check filter pressure loss first, then pipe kinks, then whether the pick-up lance is buried in material.

中文:串料串色:先查清管程序是否执行到位,再查分配阀密封与阀位反馈。

English: Cross-contamination: verify the line-clearing routine ran, then check valve seals and position feedback.

中文:输送量下降:先查风机转速与皮带,再查管路积料与弯头是否磨损穿孔。

English: Falling throughput: check fan speed and belt first, then material buildup and worn or holed bends.

中文:干燥不达标:先查回风温度与露点,再看干燥站是否被下游集中抽风打乱了风量平衡。

English: Drying out of spec: check return-air temperature and dew point, then whether concentrated downstream demand has upset the drying station's airflow balance.

六、装机验收清单

中文:逐台点动:每台机单独吸料,确认吸料时间与满料信号。

English: Per-machine jog test: load each machine alone and confirm load time and full signal.

中文:满负荷联动:全部机台同时呼叫,观察末端真空度与吸料时间是否仍在设定范围。

English: Full-load interlock: call every machine at once and watch end-of-line vacuum and load time against setpoints.

中文:清管验证:换色后取首件,确认无残留。

English: Line-clearing check: take the first part after a color change and confirm no residue.

中文:断电恢复:模拟断电重启,确认配方与料位状态能正确恢复。

English: Power recovery: simulate a restart and confirm recipes and level states restore correctly.

七、三种供料方案怎么比

中文:人工上料:投入低,但人力、粉尘与错料风险随产量上升。

相关产品 / Related Products

相关阅读 / Related Reading

自动称重配料系统

粤公网安备 44190002002288号