产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

高温模温机 High-Temperature Mold Temperature Controller|选型与功率核算

日期:2026-11-21 01:08
浏览次数:47
摘要:一、模温机在做什么 中文:模温机把导热介质(水或油)加热到设定温度,循环送入模具或辊筒流道,把模具表面温度稳定在一个窄带内。它决定的不是「加热」,而是「稳定」——温度波动直接对应制品尺寸与外观波动。 English: A mold temperature controller heats a med

一、模温机在做什么

模温机 Mold Temperature Controller


中文:模温机把导热介质(水或油)加热到设定温度,循环送入模具或辊筒流道,把模具表面温度稳定在一个窄带内。它决定的不是「加热」,而是「稳定」——温度波动直接对应制品尺寸与外观波动。


English: A mold temperature controller heats a medium (water or oil) to setpoint and circulates it through mold or roller channels, holding surface temperature in a narrow band. Its job is stability, not heating: temperature ripple maps directly to dimensional and appearance variation.


二、加热功率核算


中文:功率 = 质量 × 比热 × 温升 ÷ 时间,再乘以余量系数(参考 1.2~1.3)。例:模具与管路介质合计 50 kg 水,从 25℃ 升到 90℃,要求 20 分钟到位,则 P = 50 × 4.18 × 65 ÷ 1200 ≈ 11.3 kW,取 15 kW 机型。


English: Power = mass × specific heat × temperature rise ÷ time, times a margin factor (reference 1.2-1.3). Example: 50 kg of water in mold and piping, 25 °C to 90 °C within 20 minutes gives P = 50 × 4.18 × 65 ÷ 1200 ≈ 11.3 kW; select a 15 kW unit.


中文:导热油比热约 2.0 kJ/(kg·K),同样温升所需功率约为水的一半,但油温上限更高,适合 150℃ 以上工况。


English: Oil has a specific heat near 2.0 kJ/(kg·K), needing roughly half the power for the same rise, but supports higher temperatures for service above 150 °C.


三、流量与扬程


中文:流量按模具流道总截面积与允许温差的经验流速核算,扬程要覆盖管路阻力加模具阻力;流量不足的表现是「设定 90℃、实测进出温差超过 5℃」。


English: Flow follows channel cross-section and allowable temperature drop; head must cover piping plus mold resistance. Insufficient flow shows up as a supply-return differential above 5 °C at a 90 °C setpoint.


四、温控精度与介质选择


中文:水介质适合 ≤90~95℃、控温精度参考 ±1℃;油介质适合 150~300℃,需注意油品氧化与结焦,定期换油。


English: Water suits service up to 90-95 °C with reference accuracy ±1 °C; oil suits 150-300 °C but requires attention to oxidation and coking with scheduled oil changes.


五、常见选型错误


中文:1)按模具重量一半估功率,开机升温慢;2)只算加热不算循环,模具温差大;3)油水混用机型选错,密封件提前失效。


English: 1) Sizing power at half the calculated value causes slow heat-up; 2) ignoring circulation leaves a wide mold differential; 3) choosing the wrong oil/water variant causes premature seal failure.

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号