产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
台州冷水机 TCL-15HP 风冷分体|中型机台群降温
台州冷水机 TCL-15HP
Industrial Chiller TCL-15HP for Taizhou
台州冷水机 TCL-15HP(Industrial Chiller TCL-15HP):风冷分体一体机,出水温度 7~15℃,面向浙东及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。
Industrial Chiller TCL-15HP for Taizhou: an air-cooled unit with outlet water at 7-15 C, supplied to eastern Zhejiang and nearby cities, with cooling-load sizing, piping advice, delivery and on-site commissioning.
设备说明 / Equipment Overview
15HP 风冷机型,双风机冷凝,冷量按中等机台群配置;整机自带水箱与循环泵,接管即用,适合租用厂房或不便做土建的车间。
A 15HP air-cooled unit with twin-fan condenser sized for a mid-size machine group. Tank and pump are built in, so it works once connected, which suits rented buildings and shops where civil works are impractical.
结构与控制 / Structure & Control
机架内冷媒管路与水箱分层布置,冷凝器可做分体,把风冷模块移到室外或屋顶,室内只留主机与水泵,减少车间热负荷;电控预留通讯口,可接车间看板。
Refrigerant lines and tank are layered inside the frame, and the condenser can be split so the air-cooled section sits outdoors or on the roof while only the main body and pump stay indoors, cutting workshop heat load. A communication port ties into the shop board.
运行与精度 / Performance & Accuracy
风冷冷凝靠空气流动散热,机组四周留 1~2 米净空、别贴墙也别夹在两台设备之间;环境温度每升高 5℃,冷凝压力与电流同步上升,冷量相应下降。
Air-cooled condensers rely on airflow: leave 1-2 m clear on all sides and avoid walls or gaps between machines. Every 5 C rise in ambient lifts condensing pressure and current while cooling capacity falls.
操作与维护 / Operation & Maintenance
粉尘大的车间每月用低压气吹扫翅片,油污环境改用水洗后彻底晾干;风扇电机轴承每半年补脂,皮带传动机型一季度查张紧度;水箱每年换水并清理底部沉积。
Blow the fins monthly in dusty shops; in oily shops wash and dry them fully instead. Grease fan motor bearings every six months, check belt tension quarterly on belt-driven models, and change tank water annually with bottom sediment removed.
参数速览 / Specifications
型号 TCL-15HP|制冷量 约 13.5 kW|出水温度 7~15℃|控制精度 ±1℃|循环流量 约 45 L/min|水泵压力 0.2 MPa
Model TCL-15HP | Capacity approx. 13.5 kW | Outlet 7-15 C | Control accuracy plus or minus 1 C | Flow approx. 45 L/min | Pump pressure 0.2 MPa
应用场景 / Applications
中型注塑机群集中供冷、管材与型材线定型、吹膜与流延辊温、破碎料清洗后干燥段的恒温循环。
Central cooling for mid-size injection groups, pipe and profile calibration, roll temperature on blown film and casting lines, and constant-temperature loops in washing and drying sections for regrind.
浙东地区配套 / Local Supply in eastern Zhejiang
台州模具与日用品、汽摩配注塑企业分布广,中小企业占比高、厂房以租赁为主,倾向免土建、可移动的机组。当地夏季气温高、车间通风一般,选型多按夏季工况加余量,并优先把排热引到室外。
Taizhou spreads across mold making, household goods and auto and motorcycle parts, mostly small and medium firms in rented buildings, so units that need no civil works and can be moved are preferred. Summers are hot and ventilation is average, so sizing carries summer margin and heat rejection is pushed outdoors.
选型与交付流程 / Sizing & Delivery
按机台群的总用料量折算冷量,给出分体或一体两种布置方案与排热走向建议;到场安装后测高温时段出水温度,确认夏季很不利工况下仍能守住设定值。
We convert total throughput into a cooling load and quote both split and packaged layouts with heat-rejection routing. After installation the outlet temperature is measured during the hottest hours to confirm the set point holds under summer worst case.
常见问题 / FAQ
Q:冷量怎么算?
Q: How is the cooling capacity calculated?
A:按 Q=W×C×ΔT×S 估算:W 是每小时用料重量,C 是料种比热(PP 0.48、PE 0.55、ABS 0.40、PC 0.30 kcal/kg·℃),ΔT 取熔胶与脱模温度之差、常用 200℃,S 取 1.35~2.0;算出 kcal/h 后按 1kW=860 kcal/h 折算,再往上取一档机型。
Estimate with Q = W x C x dT x S: W is material throughput per hour, C is specific heat (PP 0.48, PE 0.55, ABS 0.40, PC 0.30 kcal/kg·C), dT is melt minus ejection temperature (200 C is typical), S is 1.35-2.0. Convert kcal/h to kW at 1 kW = 860 kcal/h, then take the next size up.
Q:风冷和水冷怎么选?
Q: Air-cooled or water-cooled?
A:有冷却塔、三班连续生产、电价偏高时用水冷,冷凝温度稳定、能耗低;缺水或没位置放塔时用风冷,接三根管就能开,夏季环境温度高于 35℃ 时冷量会掉 10%~15%,选型留余量。
Choose water-cooled when a cooling tower exists, production runs three shifts and power cost is high: condensing temperature is stable and power use is lower. Choose air-cooled when water or space is short: three pipes and it runs, but capacity drops 10-15% above 35 C ambient, so size with margin.
相关产品与内容 / Related Products
台州 本地配套与选型提示 / Local Notes for 台州
模具、汽摩配与日用品集中,再生瓶片使用量大,再生瓶片堆密度不稳,结晶干燥前先筛分除粉,混料按增重式结算。
Local industry sets the material mix in 台州, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:壳管式冷水机。
Model and configuration: 壳管式冷水机.
