产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
青岛冷水机 TCL-20HP 水冷壳管|多模集中供冷
青岛冷水机 TCL-20HP
Industrial Chiller TCL-20HP for Qingdao
青岛冷水机 TCL-20HP(Industrial Chiller TCL-20HP):水冷壳管一体机,出水温度 7~12℃,面向胶东及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。
Industrial Chiller TCL-20HP for Qingdao: a water-cooled unit with outlet water at 7-12 C, supplied to Jiaodong and nearby cities, with cooling-load sizing, piping advice, delivery and on-site commissioning.
设备说明 / Equipment Overview
20HP 水冷机型配固定塔位方案,冷凝水温稳定,连续生产时能耗优势明显;可做双回路出水,模具与料筒冷却段分开供水。
A 20HP water-cooled unit with a fixed tower position: stable condenser water and clear energy advantage in continuous production. Dual output circuits feed mold cooling and barrel cooling separately.
结构与控制 / Structure & Control
双回路出水由机内分流阀组分配,各回路独立调节流量;冷凝器为可拆壳管,水室端盖带排污口;电控箱带故障代码显示,历史报警可查,便于交接班追溯。
An internal valve manifold splits the two circuits, each with independent flow adjustment. The condenser is a serviceable shell-and-tube type with a drain on the water box, and the controller shows fault codes with alarm history for shift handover.
运行与精度 / Performance & Accuracy
连续运行时看部分负荷表现:机组多数时间不在满载,压缩机的启停频次、能量调节方式与设定水温共同决定实际电耗,设定值每抬高 1℃,耗电相应下降。
Continuous running is judged at part load: the unit rarely sits at full capacity, so actual power depends on cycling frequency, capacity control and the set point. Every 1 C raised on the set point cuts power use.
操作与维护 / Operation & Maintenance
壳管水侧按季度刷管并做水质记录,硬度高的水必须软化;排污口每班短开一次带走沉积;冬季停机排空水侧或加伴热,防止冻裂管束。
Brush the shell-and-tube water side quarterly and log water quality; hard water must be softened. Crack the drain each shift to clear sediment, and drain or trace-heat the water side in winter to avoid freezing the tubes.
参数速览 / Specifications
型号 TCL-20HP|制冷量 约 18 kW|出水温度 7~12℃|控制精度 ±1℃|循环流量 约 60 L/min|水泵压力 0.2~0.25 MPa
Model TCL-20HP | Capacity approx. 18 kW | Outlet 7-12 C | Control accuracy plus or minus 1 C | Flow approx. 60 L/min | Pump pressure 0.2-0.25 MPa
应用场景 / Applications
大件家电模具冷却、冰箱内胆与外壳模具、洗衣机桶体成型、挤出板材与片材线定型。
Cooling heavy appliance molds, refrigerator liner and shell molds, washer tub molding, and sheet and board calibration on extrusion lines.
胶东地区配套 / Local Supply in Jiaodong
青岛家电配套注塑与挤出企业集中,冰箱、洗衣机类大件模具重、冷却时间长,冷却水温度上漂,成型周期立刻拉长。当地多为三班连续生产、塔位与水处理条件齐全,倾向水冷方案按产线固定配置,并要求备件与技术支持能快速到场。
Qingdao concentrates injection and extrusion suppliers to the appliance industry. Refrigerator and washer molds are heavy with long cooling times, so any drift in coolant temperature lengthens the cycle at once. Production usually runs three shifts with tower and water treatment in place, favouring fixed water-cooled installations on each line plus fast spares and technical support.
选型与交付流程 / Sizing & Delivery
按产线的模具总冷量与同时使用率折算,给出双回路供水点的位置与管径;到场完成塔—机组—模具三段的联动调试,并按班次记录电耗与水温,为后续扩线留数据。
We convert line mold load with a simultaneity factor and specify the two supply points and pipe sizes. On site the tower, chiller and molds are commissioned as one chain, with power and water temperature logged per shift as baseline data for later line expansion.
常见问题 / FAQ
Q:一副模具配多大合适?
Q: What size suits one mold?
A:按单件重量×每小时模数×比热×温差算需求,100~250 吨机台单模多在 3~9 kW;模具重、周期长往上取,单模独配取小系数,多模共用取大值。
Work from part weight x shots per hour x specific heat x temperature difference. Most 100-250 t machines need 3-9 kW per mold; lower factor for one mold, higher when several share.
Q:水温老是波动怎么查?
Q: Why does the water temperature keep drifting?
A:先查循环流量是否够(不足时先晃后升),再看水箱水位与探头漂移;小负荷配大机时压缩机频繁启停也会锯齿波动,可改定点控温并延长很短停机时间。
Check flow first, then tank level and probe drift. A small load on a large unit cycles in saw-tooth, so use fixed set point and a longer minimum off time.
相关产品与内容 / Related Products
青岛 本地配套与选型提示 / Local Notes for 青岛
家电注塑外壳是主力,批量大、颜色相对固定,颜色固定的产线可减少色母组数量,把精度压在末组补差,日常只做零点校核。
Local industry sets the material mix in 青岛, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:壳管式冷水机。
Model and configuration: 壳管式冷水机.
