产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

宁波冷水机 TCL-20HP 水冷壳管|多模集中供冷

日期:2026-11-19 10:55
浏览次数:17
摘要:宁波冷水机 TCL-20HP Industrial Chiller TCL-20HP for Ningbo 宁波冷水机 TCL-20HP(Industrial Chiller TCL-20HP):水冷壳管一体机,出水温度 7~12℃,面向浙东及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。

宁波冷水机 TCL-20HP 整机 纯白底图

宁波冷水机 TCL-20HP
Industrial Chiller TCL-20HP for Ningbo

宁波冷水机 TCL-20HP(Industrial Chiller TCL-20HP):水冷壳管一体机,出水温度 7~12℃,面向浙东及周边地区供货,含冷量计算、管路配套建议、发货与上门调试。
Industrial Chiller TCL-20HP for Ningbo: an air-cooled unit with outlet water at 7-12 C, supplied to eastern Zhejiang and nearby cities, with cooling-load sizing, piping advice, delivery and on-site commissioning.

设备说明 / Equipment Overview

20HP 水冷机型,冷凝器走冷却水,换热效率高于风冷、单位冷量耗电低;需配冷却塔或干冷器,塔按冷量的 1.25~1.35 倍配,塔出水温度直接决定机组冷凝温度与电费。
A 20HP water-cooled unit with a water-cooled condenser: higher heat-transfer efficiency than air-cooled and lower power per unit of cooling. It needs a tower or dry cooler sized at 1.25-1.35 times the cooling load, and tower outlet temperature decides condensing temperature and the power bill.

结构与控制 / Structure & Control

壳管式冷凝器与板式蒸发器分置两侧,冷媒回路抽真空后定量充注;冷却水侧留清洗端盖,水室可拆,便于后期刷管;电控带相序、缺水、高低压与防冻保护。
Shell-and-tube condenser and plate evaporator sit on opposite sides, the refrigerant circuit is evacuated and charged by weight, and the condenser water box has a removable end cover for later tube brushing. Controls cover phase sequence, low water, high and low pressure, and freeze protection.

运行与精度 / Performance & Accuracy

冷却水进水温度越低,冷凝压力越低、同匹数冷量越大;夏季塔水温上漂时冷量随之下降,按很热月塔水温校核比按铭牌值顶格配更稳妥。
Lower condenser water inlet temperature means lower condensing pressure and more cooling from the same horsepower. Capacity falls as tower water warms in summer, so check against the hottest-month tower temperature instead of sizing on the nameplate value.

操作与维护 / Operation & Maintenance

冷却水侧按季度清洗管束,水质偏硬加装软化装置;每班查塔的水位与填料堵塞情况,风机皮带松紧一季度一调;蒸发器侧保持满水循环,避免低温段结冰冻管。
Brush the condenser tubes quarterly and fit a softener where water is hard. Check tower level and fill blockage every shift, adjust fan belt tension quarterly, and keep the evaporator loop full to avoid freezing at low set points.

参数速览 / Specifications

型号 TCL-20HP|制冷量 约 18 kW|出水温度 7~12℃|控制精度 ±1℃|循环流量 约 60 L/min|水泵压力 0.2~0.25 MPa
Model TCL-20HP | Capacity approx. 18 kW | Outlet 7-12 C | Control accuracy plus or minus 1 C | Flow approx. 60 L/min | Pump pressure 0.2-0.25 MPa

应用场景 / Applications

多副模具集中供冷、注塑机液压油与料筒冷却段、挤出定型台与冷却水槽、涂布与压延辊温控制。
Central cooling for several molds, hydraulic oil and barrel cooling zones, extrusion calibration tables and water baths, and roll temperature control on coating and calendering lines.

浙东地区配套 / Local Supply in eastern Zhejiang

宁波家电、汽配、文具与日用品注塑集群密集,模具副数多、换模频繁,冷却水温差稳不稳直接影响成型周期与外观。机台多为 100~450 吨,常按一台 20HP 水冷机带 3~6 副模具配置,塔位固定、管路走车间地沟,对连续运行能力要求高。
Ningbo runs dense injection clusters for appliances, auto parts, stationery and household goods. Many molds and frequent changes mean coolant stability drives cycle time and surface quality. Machines are mostly 100-450 t, usually one 20HP water-cooled unit feeding three to six molds, with piping in floor trenches, so continuous running matters.

选型与交付流程 / Sizing & Delivery

先按模具数量与成型周期做冷量汇总,再加 10%~20% 余量确定匹数,同时给出塔的匹配规格与管路管径;到场完成塔与机组的联动调试,记录冷却水进出温差,确保塔侧散热跟得上机组排热。
We total the load from mold count and cycle time, add 10-20% margin to fix the horsepower, and quote tower size with pipe diameters. On site the tower and chiller are commissioned together with condenser water difference logged, so tower heat rejection keeps pace with the unit.

常见问题 / FAQ

Q:一副模具配多大合适?
Q: What size suits one mold?
A:按单件重量×每小时模数×比热×温差算需求,100~250 吨机台单模多在 3~9 kW;模具重、周期长往上取,单模独配取小系数,多模共用取大值。
Work from part weight x shots per hour x specific heat x temperature difference. Most 100-250 t machines need 3-9 kW per mold; lower factor for one mold, higher when several share.

Q:水温老是波动怎么查?
Q: Why does the water temperature keep drifting?
A:先查循环流量是否够(不足时先晃后升),再看水箱水位与探头漂移;小负荷配大机时压缩机频繁启停也会锯齿波动,可改定点控温并延长很短停机时间。
Check flow first, then tank level and probe drift. A small load on a large unit cycles in saw-tooth, so use fixed set point and a longer minimum off time.

相关产品与内容 / Related Products

宁波 本地配套与选型提示 / Local Notes for 宁波

余姚、慈溪一带家电与汽配集中,模具配套成熟,家电件颜色多、批量中等,配方号与色号分开管理,换色只清下料口。
Local industry sets the material mix in 宁波, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:壳管式冷水机。
Model and configuration: 壳管式冷水机.

相关阅读 / Related Reading

粤公网安备 44190002002288号