产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

真空上料与气力输送系统 负压输送的选型参数与常见故障 Vacuum Conveying Selection and Troubleshooting

日期:2026-11-21 05:43
浏览次数:48
摘要:一、这套系统解决什么问题 | What This System Solves 注塑、挤出、吹膜车间把原料从储料区送到机台,无非两条路:人工搬运,或者气力输送。人工搬运的问题是粉尘、撒漏、混料错料、以及每班多出来的体力消耗;气力输送把这条线做成闭路,料在管道里走,人在旁边看表。 In molding,

一、这套系统解决什么问题 | What This System Solves

注塑、挤出、吹膜车间把原料从储料区送到机台,无非两条路:人工搬运,或者气力输送。人工搬运的问题是粉尘、撒漏、混料错料、以及每班多出来的体力消耗;气力输送把这条线做成闭路,料在管道里走,人在旁边看表。

In molding, extrusion and film plants resin moves from storage to machine by manual handling or by pneumatic conveying. Manual handling brings dust, spillage, wrong-material mistakes and wasted labor; pneumatic conveying makes the route a closed loop. This article covers vacuum conveying: sizing, piping layout and troubleshooting.

二、负压输送是怎么工作的 | How Vacuum Conveying Works

真空泵在管路末端抽气,管内形成负压,料斗里的颗粒被气流带起,经吸料管进入分离器;过滤器把料与气分开,料落进料斗,气经真空泵排空。一个工作循环由吸料、满料停机、放料、再吸料构成,节拍由料位信号或时间继电器控制。

The pump evacuates air at the end of the line, creating negative pressure; granules are lifted by the air stream into the receiver, separated from air by a filter, and fall into the hopper. One cycle is pick-up, full-load stop, discharge, pick-up, timed by a level signal or a relay.

常见配置是「一泵带多机」:一台真空泵通过分配站轮流服务多台机台,靠阀门切换;单机独立泵适合料量大、换料频繁的场合。

One pump can serve several machines through a distribution station with valve switching; a dedicated pump per machine suits high throughput or frequent changes.

三、选型要定的六个参数 | Six Parameters to Fix Before Sizing

其一,输送量。按机台每小时峰值耗料量乘以 1.2~1.5 的余量;多机共泵时按同时吸料机台的数量叠加,而不是简单相加全部机台。

First, conveying capacity. Take the machine's peak hourly consumption and multiply by 1.2–1.5. When several machines share one pump, add up only the machines drawing at the same time, not the whole plant.

其二,输送距离与提升高度。水平段与垂直段的阻力特性不同,垂直提升每米都要额外的静压,管路越长、弯头越多,所需真空度越高。

Second, distance and lift. Horizontal and vertical sections resist differently; every meter of lift costs static pressure, and longer runs with more elbows need higher vacuum.

其三,物料形态。颗粒料、粉料、破碎料的气流速度与过滤方式都不一样;粉料要低速、要更大的过滤面积,颗粒料可以快一些。

Third, material form. Granules, powders and regrind need different air velocity and filtration; powders require lower speed and larger filter area, granules tolerate higher speed.

其四,真空源形式。旋片泵、罗茨泵、真空发生器各有适用区间:短距离小流量可用发生器,长距离或多点共用选旋片泵,大流量高负压用罗茨泵配前级泵。

Fourth, vacuum source type. Rotary-vane pumps, roots blowers and vacuum generators each fit a range: generators for short runs and small flow, vane pumps for longer runs or multiple points, roots blowers with a backing pump for high flow and deep vacuum.

其五,过滤精度与清灰方式。过滤器堵了,输送量会先掉一半再报警,所以清灰方式(脉冲反吹、手动、自动抖袋)要在选型时就定下来。

Fifth, filtration rating and cleaning method. A clogged filter halves throughput before any alarm appears, so the cleaning method (pulse jet, manual, automatic bag shake) must be decided at the selection stage.

其六,控制层级。单机就地控制、集中控制柜、还是接入车间 PLC 与上位机;这决定了后期能不能做料位联动、缺料报警、用量统计。

Sixth, control level: local control, a central cabinet, or integration with the plant PLC and host system. This decides whether level interlocking, material-out alarms and consumption statistics are possible later.

四、管路布置的五个硬要求 | Five Hard Rules for Piping

一、弯头越少越好,弯头处是磨损与积料的高发点;二、水平段要有足够的气流速度,粉料尤其不能低速长距离平推;三、吸料口要装补气装置,否则管内会「憋料」;四、分配站与机台之间留检修空间;五、管路要做静电与接地处理,粉体输送尤其注意。

Keep elbows to a minimum, since they wear and accumulate material; keep enough air velocity in horizontal runs, especially for powders; fit an air intake at the pick-up point to avoid slugging; leave service space between the distribution station and machines; and provide static grounding, particularly for powder lines.

五、现场常见故障与排查顺序 | Troubleshooting Order on Site

吸不上料,先看补气口是否被堵,再看过滤器是否糊死,再测真空度是否达到设定值。输送量下降,按过滤器、管路积料、真空泵皮带与叶片、料位设定四项依次排除。串料混料,多半是分配站阀门关闭不严或清管程序缺失,需要加吹扫。

For no pick-up: check the air intake first, then the filter, then the actual vacuum level. For falling throughput: work through filter, pipe build-up, pump belt and vanes, and level settings in that order. For cross-contamination: usually a leaking distribution valve or a missing purge routine.



相关阅读 / Related Reading

自动称重配料系统

粤公网安备 44190002002288号