产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

结晶与除湿干燥工艺参数全书:露点、温度、时间怎么配 Crystallizing & Drying Parameters

日期:2026-11-21 02:15
浏览次数:57
摘要:一、先把三道工序分开 中文:结晶:把无定形料加热到结晶温度区间,让颗粒表面硬化、结晶度上升,解决的是「进入干燥段后结块堵料」。 English: Crystallizing heats amorphous resin into the crystallization band so pellets

一、先把三道工序分开

PET 结晶干燥机 PET Crystallizer

中文:结晶:把无定形料加热到结晶温度区间,让颗粒表面硬化、结晶度上升,解决的是「进入干燥段后结块堵料」。

English: Crystallizing heats amorphous resin into the crystallization band so pellets harden and crystallinity rises, solving caking and blockage in the drying stage.

中文:除湿:把空气里的水分拿掉,产出低露点干风,解决的是「空气携湿能力不足」。

English: Dehumidifying strips moisture from the air to produce low-dew-point dry air, solving insufficient moisture-carrying capacity.

中文:干燥:用低露点热风穿透料层,把料内水分带到目标含水率,解决的是「原料本身含水超标」。

English: Drying passes low-dew-point hot air through the bed to bring moisture down to target, solving excessive moisture in the resin itself.

中文:三道工序的分工认错,就会出现「除湿机开足、料还是湿」的无效努力。

English: Mixing up the three roles produces the classic waste of running the dehumidifier flat out while the resin stays wet.

二、六类原料的参数对照(参考范围)

中文:PET 全新料:料温 170~175℃,露点 ≤-40℃,停留 4~6h,目标含水 ≤50ppm。

English: Virgin PET: 170–175 °C, dew point ≤-40 °C, 4–6 h, target ≤50 ppm.

中文:PET 瓶级(碳酸瓶):料温 170~175℃,露点 -45~-50℃,停留 5~6h,目标 ≤30ppm。

English: Bottle-grade PET for carbonated drinks: 170–175 °C, dew point -45 to -50 °C, 5–6 h, target ≤30 ppm.

中文:rPET 回收瓶片:料温 160~170℃,露点 ≤-40℃,停留 2~3h,目标 ≤60~80ppm,时间过长会加剧黏度损失。

English: Recycled flakes: 160–170 °C, dew point ≤-40 °C, 2–3 h, target ≤60–80 ppm; longer dwell accelerates viscosity loss.

中文:PLA:料温 60~90℃,露点 ≤-30℃,停留 2~4h,温度过高会软化粘连。

English: PLA: 60–90 °C, dew point ≤-30 °C, 2–4 h; higher temperatures soften and stick.

中文:PA(尼龙):料温 80~100℃,露点 ≤-35℃,停留 3~5h,注意氧化变色。

English: PA: 80–100 °C, dew point ≤-35 °C, 3–5 h; watch for oxidative discoloration.

中文:TPU:料温 70~100℃,按牌号取值,停留 2~3h,温度偏高会粘连成团。

English: TPU: 70–100 °C by grade, 2–3 h dwell; overshooting causes clumping.

三、露点怎么定,不是越低越好

中文:露点越低,除湿能耗越高。按制品敏感度分档取:

English: Lower dew point costs more energy. Choose by product sensitivity:

中文:一般注塑:-20~-30℃ 足够。

English: General injection: -20 to -30 °C is enough.

中文:瓶胚与薄膜:≤-40℃。

English: Preforms and film: ≤-40 °C.

中文:碳酸瓶、光学件:-45~-50℃。

English: Carbonated bottles and optical parts: -45 to -50 °C.

中文:判断标准不是仪表数字好看,而是出料含水率与制品表现(气泡、银纹、强度)是否达标。

English: The criterion is outlet moisture and part quality (bubbles, silver streaks, strength), not a impressive gauge reading.

四、温度边界与两条红线

中文:下限:低于 160℃(PET)时,水分从颗粒芯部扩散太慢,停留再久也达不到目标。

English: Lower limit: below 160 °C for PET, moisture diffusion from the pellet core is too slow for any dwell time.

中文:上限:高于 185℃(PET)时,降解与黄变加速,黏度下降,制品强度掉。

English: Upper limit: above 185 °C for PET, degradation and yellowing accelerate and viscosity drops.

中文:所以温度窗口是「够快但不伤料」,不是越高越好。

English: The window is fast enough without damaging the resin, not as hot as possible.

五、除湿方式怎么选

中文:蜂巢转轮:露点可达 -40℃ 以下,连续供风稳定,占地小;再生温度 180~250℃,运行能耗主要在再生。

English: Honeycomb rotor: below -40 °C dew point, continuous stable supply, compact footprint; regeneration at 180–250 °C dominates running cost.

中文:双塔吸附:露点一般 -30℃ 左右,投入低,但切换时露点有波动,适合间歇生产。

English: Twin-tower adsorption: around -30 °C dew point, low capex, dew point swings on switching, suited to intermittent production.

中文:氮气闭环:用于易氧化的原料,抑制氧化降解,成本高于空气系统。

English: Closed-loop nitrogen suits oxidation-prone resins and suppresses degradation, at higher cost than air systems.

六、调试顺序:先风量,再温度,后露点,末了时间

中文:顺序错了就会反复试。正确顺序是:先确认风量能穿透料层,再定温度窗口,再定露点档位,再调停留时间。

English: Wrong order means endless trial. Correct order: confirm airflow penetrates the bed, set the temperature window, choose the dew-point tier, then tune dwell.

中文:只调时间不改风量,是常见的无效调试:料层没穿透,加时间只是让上层更干、下层依旧湿。

English: Tuning dwell alone is the usual wasted effort: with an unpenetrated bed, more time only over-dries the top layer.

七、常见故障对照

中文:含水率不达标:先查露点,再查风量,再看停留时间是否被生产节拍压缩。

English: Moisture out of spec: check dew point, then airflow, then whether dwell has been squeezed by production rhythm.

中文:料斗结块:先查结晶段是否到位,再看料温是否超过软化点。

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号