产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

青岛机边粉碎机 TGC-500 中速带风送|多机集中回收

日期:2026-11-21 04:59
浏览次数:37
摘要:青岛机边粉碎机 TGC-500 Medium-speed Granulator TGC-500 for Qingdao 青岛机边粉碎机 TGC-500(Medium-speed Granulator TGC-500):中速机型,4 kW 电机,转速约 360 r/min,配 Ф8 筛网,带旋风分离器

青岛机边粉碎机 TGC-500 整机 纯白底图

青岛机边粉碎机 TGC-500
Medium-speed Granulator TGC-500 for Qingdao

青岛机边粉碎机 TGC-500(Medium-speed Granulator TGC-500):中速机型,4 kW 电机,转速约 360 r/min,配 Ф8 筛网,带旋风分离器与送料风机。
Medium-speed Granulator TGC-500 for Qingdao: medium-speed type with a 4 kW motor at about 360 rpm, 8 mm screen, cyclone separator and conveying blower

设备说明 / Equipment Overview

中速机型配旋风分离器与送料风机,粉碎料直接送回料斗,适合水口较大的家电件与多台机集中回收;机身加隔音棉,运转时车间噪声可控。
With cyclone and blower the regrind returns straight to the hopper, which suits large appliance sprues and multi-machine reclaim. Acoustic lining keeps shop noise within limits.

结构与控制 / Knife Frame & Control

片刀型刀架,动刀 21 片、定刀 2 片,同为 SKD-11;送料风机 0.75 kW 独立回路,与主电机联锁,风机未启动主机不转;电控为电脑板加过载与门锁保护。
A segmented rotor carries 21 rotating and 2 fixed SKD-11 knives. The 0.75 kW blower runs on its own circuit interlocked with the main motor, so the grinder will not start with the blower off; the controller adds overload and door interlocks.

运行与精度 / Output Size & Running Behaviour

中速靠高速冲击加剪切,出料快、单次投入量大;筛网孔径决定粒径,Ф8 适合多数家电件回用,需更细颗粒时换 Ф6 并同步降低投料速度,避免堵腔。
Impact plus shear at medium speed gives fast output and larger single feeds. The screen sets grain size: 8 mm suits most appliance reclaim, and switching to 6 mm needs a slower feed rate to avoid clogging.

操作与维护 / Knife Care & Cleaning

每班清筛网与集料盒,风管一周拆检一次防堵;刀具按产量磨,硬质料磨刀周期更短,建议常备一组刀具备换;每月清旋风分离器内壁结粉,避免回料掺入脏料。
Clear the screen and bin each shift and strip the duct weekly against blockage. Regrind by output; hard materials need shorter intervals, so keep one spare set. Wipe the cyclone wall monthly so dirty powder does not re-enter the blend.

参数速览 / Specifications

中速机型,4 kW 电机,转速约 360 r/min,配 Ф8 筛网,带旋风分离器与送料风机。
medium-speed type with a 4 kW motor at about 360 rpm, 8 mm screen, cyclone separator and conveying blower

应用场景 / Applications

家电外壳、周转箱与大件包装的水口与欠佳品破碎,也用于挤出开机料、片材边料的减容处理。
Grinding sprues and rejects from appliance shells, crates and large packaging, plus start-up lumps and sheet trim on extrusion lines.

胶东地区配套 / Local Supply in Jiaodong

青岛家电配套注塑企业以大件制品为主,水口重、单班量大,常把两三台机的回料汇到一台中速机处理。当地对连续运行与粉尘管理要求高,倾向带旋风分离与除尘的组合方案。
Qingdao appliance molders run large parts with heavy sprues and high volume per shift, often routing regrind from two or three presses into one medium-speed unit. Continuous running and dust control are taken seriously, so cyclone separation with dust collection is the usual choice.

选型与交付流程 / Sizing & Delivery

按单班水口总量与较大单件尺寸选腔体口径,再定送料管路走向与回料点;到场完成风机—主机联锁测试与回料比例标定,确保回收料进入料斗时不会冲淡配比。
Chamber size follows sprue volume per shift and the largest single piece; then duct routing and return points are fixed. On site we test the blower interlock and calibrate the blend ratio so the reclaim does not dilute the recipe.

常见问题 / FAQ

Q:带风机会把粉尘带进料斗吗?
Q: Does the blower carry dust into the hopper?
A:配旋风分离器后粉料与气流分开,颗粒落桶、粉尘进过滤袋;回用要求高时在送料管末端加一道筛分或除尘模块。
With a cyclone the air stream separates from the regrind, so grain falls into the bin and dust goes to a filter bag. For high-grade reclaim, add a screening or dust stage at the end of the conveying line.

Q:多台机共用一台要注意什么?
Q: What matters when several presses share one unit?
A:按同时出料的总量选腔体,管路做分支并加切换阀,避免一台机的水口在另一台机换色时混料;每条支管留清料口,换色时先吹干净再开阀。
Size the chamber on simultaneous output, branch the ducting with selector valves so one press does not mix colours into another, and leave a purge point on each branch to blow clean before opening the valve.

相关产品与内容 / Related Products

青岛 本地配套与选型提示 / Local Notes for 青岛

家电注塑外壳是主力,批量大、颜色相对固定,颜色固定的产线可减少色母组数量,把精度压在末组补差,日常只做零点校核。
Local industry sets the material mix in 青岛, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:中速机边粉碎机。
Model and configuration: 中速机边粉碎机.

相关阅读 / Related Reading

粤公网安备 44190002002288号