产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
余姚慢速机边粉碎机 TGC-300 慢速剪切|硬质水口就地回收
余姚慢速机边粉碎机 TGC-300
Slow-speed Granulator TGC-300 for Yuyao
余姚慢速机边粉碎机 TGC-300(Slow-speed Granulator TGC-300):慢速剪切机型,2.2 kW 减速电机直驱,转速约 145 r/min,配 Ф5 筛网(可选 Ф4~Ф12)。
Slow-speed Granulator TGC-300 for Yuyao: low-speed shear type with a 2.2 kW geared motor driving the rotor at about 145 rpm and a 5 mm screen (4-12 mm optional)
设备说明 / Equipment Overview
机边就地回收,水口料从机械手或输送带直接落进料斗,粉碎后经风机送回料斗按比例掺用,省掉集中粉碎的周转与二次污染;腔体与刀架模块化,清料换色时整块抽出即可。
Reclaim happens beside the press: sprues drop from the robot or conveyor into the hopper, are granulated and blown back into the hopper for ratio blending, skipping central grinding and its extra handling. Chamber and knife frame are modular, so a colour change means pulling one block out.
结构与控制 / Knife Frame & Control
SKD-11 动刀与定刀(硬度 58~60)配进口减速电机直驱,无皮带传动、动力损耗低;配过载保护、卡料反转与急停按钮,料斗为不锈钢双层结构,可选旋风分离器与除尘模块。
SKD-11 rotating and fixed knives at 58-60 HRC, driven through a geared motor with no belt losses. Overload protection, jam reversal and an emergency stop are standard; the hopper is double-wall stainless, with cyclone and dust module available.
运行与精度 / Output Size & Running Behaviour
低速剪切为主、搓磨为辅,颗粒形状规整、细粉占比低,回用后制品强度与色泽波动小;出料粒径由刀型与筛网孔径共同决定,孔径每放大一档,产量上升、回用比例需相应下调。
Low-speed shear with light rubbing gives regular grain and little fines, so strength and colour vary less after reclaim. Output size follows knife geometry and screen opening: one step larger raises throughput but the blend ratio should come down.
操作与维护 / Knife Care & Cleaning
每班清腔体与筛网残留,避免不同颜色交叉;每周查刀口间隙与紧固螺栓,出料变粗或电流上升时安排磨刀;每月给轴承补脂、清理风机叶轮积粉,定期试急停与门锁开关。
Clear the chamber and screen every shift to stop colour cross-over. Check knife clearance and bolts weekly, and regrind when output coarsens or current rises. Grease bearings and clear blower dust monthly, and test the stop and door switches regularly.
参数速览 / Specifications
慢速剪切机型,2.2 kW 减速电机直驱,转速约 145 r/min,配 Ф5 筛网(可选 Ф4~Ф12)。
low-speed shear type with a 2.2 kW geared motor driving the rotor at about 145 rpm and a 5 mm screen (4-12 mm optional)
应用场景 / Applications
机边水口料、浇口与少量欠佳品的就地回收,适合 ABS、PC、POM、PS 等硬质料,可与机械手、输送带、比例阀组成自动回用回路。
In-line reclaim of sprues, gates and a few rejects, suited to hard ABS, PC, POM and PS, and combinable with robots, conveyors and ratio valves into an automatic loop.
浙东地区配套 / Local Supply in eastern Zhejiang
余姚一带以**塑料城为核心的改性料与家电注塑集群,料种杂、换色频繁,ABS、PC、POM 硬质水口占比高。车间多为多机台小批量排产,倾向机边就地回收、按比例直接掺用,对清料便利性与粉尘控制要求高。
Yuyao, home to the China Plastics City market, mixes compound trading with appliance molding. Many materials, frequent colour changes and a high share of hard ABS, PC and POM sprues mean shops prefer reclaim right at the machine and blend it back in ratio, with easy cleaning and dust control.
选型与交付流程 / Sizing & Delivery
提供水口单件重量、单班产量与回料粒径要求后,给出腔体口径与刀型建议、回料输送方式与安装位布局;签约后按交期发运,到场安装、试粉碎、调刀并培训,随机附操作手册与备用刀片清单。
Send sprue weight, output per shift and required regrind size, and we reply with chamber size, knife pattern, reclaim method and layout. After order we ship on schedule, install, run a trial grind, set knives and train operators, with manual and spare blade list.
常见问题 / FAQ
Q:慢速和高速怎么选?
Q: Slow or high speed?
A:慢速剪切为主,粉料少、噪音低、颗粒规整,回用比例可以放大;高速靠冲击破碎,产量高但细粉多、磨损快,更适合薄壁大水口与集中回收。
Slow speed shears and produces few fines with low noise and regular grain, so a higher reclaim ratio is safe. High speed breaks by impact for more output, but fines and knife wear rise, which suits thin-wall sprues and central reclaim.
Q:无筛网和有筛网差在哪?
Q: Screenless or screened?
A:无筛网机型靠刀型与转速决定颗粒大小,出料偏粗时换小间隙刀架;有筛网机型直接按孔径选 Ф4~Ф12,孔径越小越细、产量相应下降。
On screenless units knife geometry and speed set the grain, so a tighter frame is fitted when output runs coarse. Screened units take a 4-12 mm screen: smaller opening means finer grain and lower throughput.
相关产品与内容 / Related Products
余姚 本地配套与选型提示 / Local Notes for 余姚
家电、模具与小家电配套集中,试模频繁,试模频繁建议配一台小型混料机专门打样,量产机不反复清机。
Local industry sets the material mix in 余姚, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:中速机边粉碎机。
Model and configuration: 中速机边粉碎机.
