产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

结晶机工艺参数怎么定:结晶温度、停留时间与结晶度 Crystallization Parameters

日期:2026-11-21 00:58
浏览次数:47
摘要:一、结晶这道工序到底解决什么 中文:无定形 PET 在超过玻璃化温度后会软化粘连,直接进干燥料斗就结块、堵料,干燥风穿不透。结晶的作用是把颗粒表面先硬化,提升软化点,让后面的干燥段能正常进行。 English: Amorphous PET softens and sticks above its g

一、结晶这道工序到底解决什么

PET 结晶干燥机 PET Crystallizer


中文:无定形 PET 在超过玻璃化温度后会软化粘连,直接进干燥料斗就结块、堵料,干燥风穿不透。结晶的作用是把颗粒表面先硬化,提升软化点,让后面的干燥段能正常进行。


English: Amorphous PET softens and sticks above its glass transition temperature; feeding it straight into a drying hopper produces caking and blockage with no air penetration. Crystallization hardens the pellet surface and raises the softening point so drying can proceed.


中文:判定标准不是「看着不粘」,而是结晶度:常规要求 ≥30%,瓶级与薄膜级按工艺卡取值。


English: The criterion is not visual stickiness but crystallinity: ≥30 % is the common requirement, with bottle and film grades per their process card.


二、温度:分两段取


中文:预热段 120~160℃,让料温先均匀升上来;主结晶段 160~180℃,完成分子链重排。


English: Pre-heat at 120–160 °C to even out the bed temperature, then main crystallization at 160–180 °C to complete chain rearrangement.


中文:温度上限的意义在于防黄变:超过 185℃ 后,降解与色变速度上升,即使结晶度达标也不划算。


English: The upper limit matters for yellowing: beyond 185 °C degradation and color shift accelerate, so higher crystallinity is not worth it.


中文:温度均匀性是隐性参数,罐内温差建议控制在 ±2℃ 以内;温差大就会出现局部结块与局部未结晶并存。


English: Temperature uniformity is the hidden parameter: keep the in-vessel spread within ±2 °C, otherwise local caking coexists with un-crystallized material.


三、停留时间:按粒径与设备形式分


中文:塔式/卧式连续结晶器:停留 20~40 分钟;间歇式结晶罐:按批取 30~60 分钟。


English: Continuous tower or horizontal crystallizers need 20–40 min dwell; batch vessels take 30–60 min per batch.


中文:粒径越小,热量传到芯部越快,停留时间可取下限;片状边料比颗粒更薄,时间更短。


English: Smaller particles conduct heat to the core faster, so dwell can approach the lower bound; flake trimmings are thinner than pellets and need less time.


四、搅拌与排气


中文:搅拌转速参考 10~20 rpm:转速过低防不住抱团,过高则磨料、粉尘增多。


English: Agitator speed of roughly 10–20 rpm: too slow fails to prevent clustering, too fast increases attrition and dust.


中文:结晶过程会释放水分与少量挥发物,需要排气通道;密闭不做排气的罐体,容易出现料层上方潮气滞留。


English: Crystallization releases moisture and traces of volatiles, so a vent path is required; a sealed vessel without venting traps humidity above the bed.


五、不同原料的调整方向(参考)


中文:全新瓶级 PET:温度 160~175℃,停留 30~40 分钟,目标结晶度 ≥30%。


English: Virgin bottle-grade PET: 160–175 °C, 30–40 min, target crystallinity ≥30 %.


中文:rPET 回收瓶片:杂质与水分偏高,温度取 150~165℃,停留缩短、排气加强,避免黏度进一步下降。


English: Recycled flakes: with higher contaminants and moisture, run 150–165 °C with shorter dwell and stronger venting to avoid further viscosity loss.


中文:PLA:结晶温度明显低于 PET,一般取 100~120℃,温度过高会软化结块。


English: PLA crystallizes well below PET, typically 100–120 °C; higher temperatures cause softening and caking.


中文:TPU:按牌号硬度设定,硬度越高,可取的结晶温度越高;参数须以牌号技术数据表为准。


English: TPU is grade-specific: harder grades tolerate higher crystallization temperatures; settings follow the grade data sheet.


六、结晶段与干燥段怎么衔接


中文:结晶后物料带着显热进入干燥料斗,能缩短干燥升温时间;两段之间不宜长时间敞口存放,否则重新吸潮,前面的结晶白做。


English: Crystallized material carries sensible heat into the drying hopper and shortens heat-up; avoid long open-air transfer between stages, or re-absorbed moisture undoes the crystallization work.


中文:一体机把两段做在同一机架上,热损失更少;分体式则便于既有产线分段改造。


English: Combination units put both stages on one frame with less heat loss; split designs ease staged retrofits of existing lines.


注:以上参数为行业通用参考范围,实际以物料工艺卡与设备手册为准。


English: Note: the values above are industry reference ranges; actual settings follow the material process card and machine manual.

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号