产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

PET 除湿干燥机选型对照:露点、风量、停留时间怎么定 PET Dehumidifying Dryer Selection

日期:2026-11-21 06:25
浏览次数:54
摘要:一、先定露点,再定机型 中文:露点是干燥能力的上限,不是越高越好。行业通用取法:瓶级与薄膜级取露点 ≤-40℃,稳定运行为 -45~-50℃;纤维与一般注塑可取 -20~-30℃;对水分敏感的光学件按工艺卡要求单独设定。 English: Dew point sets the ceiling of

一、先定露点,再定机型

PET 除湿干燥机 Desiccant Dryer

中文:露点是干燥能力的上限,不是越高越好。行业通用取法:瓶级与薄膜级取露点 ≤-40℃,稳定运行为 -45~-50℃;纤维与一般注塑可取 -20~-30℃;对水分敏感的光学件按工艺卡要求单独设定。

English: Dew point sets the ceiling of drying capability, not simply the higher the better. Industry practice: ≤-40 °C for bottle and film grades with -45 to -50 °C in steady operation; -20 to -30 °C for fiber and general injection; optical parts follow the process card.

中文:判断依据是目标含水率:瓶级 PET 通常要求 ≤50 ppm,碳酸瓶更严,取 ≤30 ppm。

English: The driver is target moisture: bottle-grade PET typically ≤50 ppm, carbonated bottles tighter at ≤30 ppm.

二、蜂巢转轮与双塔吸附怎么选

中文:蜂巢转轮:露点可到 -40℃ 以下,连续供风、温湿度平稳,占地小;再生温度约 180~250℃,再生能耗是主要运行成本。

English: Honeycomb rotor: reaches below -40 °C dew point with continuous, stable air and a small footprint; regeneration runs at roughly 180–250 °C and dominates running cost.

中文:双塔吸附:露点一般在 -30℃ 上下,设备投入低,但切换时露点有波动,适合中小批量与不连续生产。

English: Twin-tower adsorption: dew point around -30 °C, lower capex, but dew point swings during switching; suited to small batches and intermittent production.

中文:取法:连续产线、瓶坯高速机选转轮;间歇生产、小批量多牌号可选双塔。

English: Selection: rotors for continuous lines and high-speed preform machines; twin towers for intermittent, small-lot multi-grade work.

三、风量按料层截面配,不按机型配

中文:风量决定热风能否穿透料层。料层越厚、粒径越细,所需风量越大;风量不足时上层干、下层湿,出料含水率波动。

English: Airflow decides whether hot air penetrates the bed. Thicker beds and finer particles need more air; insufficient airflow dries the top layer while the bottom stays wet.

中文:参考做法:按料斗截面积取空塔风速,再核算每公斤物料的风量比,再以出料含水率实测校核。

English: Reference method: set superficial velocity from the hopper cross-section, convert to airflow per kilogram of material, then verify against measured outlet moisture.

中文:过滤器与管路压损常被忽略,压损偏大等于风量打折,选风机时要留余量。

English: Filter and duct pressure loss is often overlooked; excess pressure loss cuts effective airflow, so fans need head margin.

四、停留时间按原料分档

中文:全新料静态料斗:4~6 小时;动态搅拌料斗:2.5~4 小时。

English: Virgin material: 4–6 h in a static hopper, 2.5–4 h with agitation.

中文:rPET 回收瓶片:温度下调 5~10℃,停留 2~3 小时,时间过长会加剧黏度降解。

English: Recycled flakes: lower the temperature by 5–10 °C and hold 2–3 h; longer dwell accelerates viscosity loss.

中文:温度边界:低于 160℃ 时水分从芯部扩散慢,难以达标;高于 185℃ 时降解与黄变风险上升。

English: Temperature limits: below 160 °C moisture diffusion from the core is too slow; above 185 °C degradation and yellowing rise.

五、三类原料参数对照(参考范围)

中文:瓶级新料:料温 170~175℃,露点 ≤-40℃,停留 4~6h,目标 ≤50ppm。

English: Bottle-grade virgin: 170–175 °C, dew point ≤-40 °C, 4–6 h, target ≤50 ppm.

中文:碳酸瓶料:料温 170~175℃,露点 -45~-50℃,停留 5~6h,目标 ≤30ppm。

English: Carbonated bottle grade: 170–175 °C, dew point -45 to -50 °C, 5–6 h, target ≤30 ppm.

中文:rPET 瓶片:料温 160~170℃,露点 ≤-40℃,停留 2~3h,目标 ≤60~80ppm。

English: rPET flakes: 160–170 °C, dew point ≤-40 °C, 2–3 h, target ≤60–80 ppm.

注:以上为行业通用参考范围,实际以物料工艺卡与设备手册为准。

English: Note: these are industry reference ranges; the actual setting follows the material process card and machine manual.

六、三个常见误判

中文:误判一:只看露点不看风量,露点达标但料层未穿透,出料仍不合格。

English: Misjudgement one: watching dew point but not airflow, so the bed is not penetrated and outlet moisture still fails.

中文:误判二:为求快提高温度,超过 185℃ 后颜色变黄、黏度下滑,反而要降负荷。

English: Misjudgement two: raising temperature for speed; beyond 185 °C yellowing and viscosity loss force a lower throughput.

中文:误判三:料斗不做保温,热风在中途散热,实际进料温度低于显示值。

English: Misjudgement three: uninsulated hoppers lose heat en route, so the real inlet temperature is below the displayed value.

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号