产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
常州型材与异型材线挤出称重式混料机 GW-300|Profile Gravimetric Blender
常州型材与异型材线挤出称重式混料机 GW-300|Profile Gravimetric Blender
Gravimetric Blender GW-300 for Profile And Window Lines
型材与异型材线用GW-300 这条线很怕的是配比漂了没人发现:颜色慢慢偏、厚薄慢慢变,等到成品抽检才发现,已经废了一批。
The risk on profile and window lines is a drifting blend nobody notices until a sample fails, with a whole batch already made.
术语对照 / Terminology
| 中文 | English | 本地语言 / Local |
|---|---|---|
| 称重式混料机 | Gravimetric Blender | Gravimetric Blender |
| 批量称重混料机 | Gravimetric Batch Blender | Batch Blender |
| 失重式混料机 | Loss-in-Weight Blender | LIW Blender |
| 多组份配料 | Multi-Component Dosing | Multi-Component Dosing |
市场与定位 / Market & Positioning
型材断面复杂,各组分到达机头的时间差会在断面颜色上体现,混料座必须短程高效。
Complex profiles expose arrival timing as colour bands across the section, so the mixing seat must blend over a short path.
结构组成 / Construction
上部计量料斗按组份数排布,每斗独立计量螺杆与称重传感器;中部混料座带拌料器;下部出料口直落挤出机进料口,全程不经过长距离气力输送,减少偏析与残料。
Weighing hoppers sit on top with independent screws and load cells, a mixing seat with stirrer sits in the middle, and the outlet drops straight into the extruder throat without long pneumatic conveying.
计量与精度 / Metering & Accuracy
按增重法逐组称量,末组补差;单组偏差常见 0.1% 量级,批次越大相对偏差越小。低比例色母的稳定性取决于称重分辨率与补料节拍。
Each group is weighed by gain with the last group trimming the total, per-group deviation commonly near 0.1 percent and improving with larger batches, while low-share stability depends on resolution and refill cadence.
电气与安装 / Electrical & Installation
装在挤出机进料口正上方,出料口与进料口中心对齐;机架调平后加减振垫,通电前空跑校零,再用实物砝码逐斗复核。
Mounted directly above the throat with centres aligned, levelled on isolation pads, zeroed empty and checked per hopper with test weights.
参数速览 / Specifications
型号 GW-300|组份 3~4 组|单批 1~20 kg|产量 5~150 kg/h|料斗 15~40 升|驱动 步进与直流调速|控制 触控屏 配方 20 组
Model GW-300 | 3-4 components, 1-20 kg batch, 5-150 kg/h, 15-40 litre hoppers, stepper and DC drives, 20 recipes
适配场景 / Applications
适配 型材与异型材线;也可用于来料批次掺混、再生料与新料配比、机边小批量打样。
Suited to profile and window lines, also incoming batch blending, virgin and regrind proportioning and machine-side sampling.
常见问题 / FAQ
Q:这台在型材与异型材线上要配多少组?
Q: How many components for profile and window lines?
A:按配方里有几种料定:单一配比 3 组够,含回料与两种助剂就上 5 至 6 组,扩产不必换机。
Count the materials in the recipe: three loops for a simple blend, five or six with regrind and two additives, avoiding a later replacement.
Q:换配方要多久?
Q: How long is a recipe change?
A:存过配方的直接调号,一分钟内开始称量;全新配方输入比例即可,不必重设转速。
A stored recipe recalls in under a minute, and a new one needs only ratios rather than speed settings.
