产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

苏州3D打印PETG除湿干燥机 TCD-300|切片前处理防气泡

日期:2026-11-21 00:18
浏览次数:9
摘要:苏州PETG除湿干燥机 TCD-300,蜂巢转轮把露点压到 -40℃ 以下,切片进挤出机前完成均温均湿,减少气泡与断丝。 / Honeycomb rotor dryer TCD-300 holding dew point below minus 40 C before PETG enters the extruder.

耗材线干燥段 车间实景

苏州3D打印PETG除湿干燥机 TCD-300|切片前处理防气泡
PETG Dehumidifying Dryer TCD-300 for Filament

PETG 与 PLA 吸湿,含水率在千分之几就能在挤出段冒泡,线材内部出现空腔;干燥段不稳,后面的配比与测径再准也白搭。
PETG and PLA absorb moisture, and a few parts per thousand is enough to bubble in the extruder and leave voids in the filament, so unstable drying defeats accurate dosing and gauging downstream.

设备说明 / Equipment Overview

蜂巢转轮分区工作,处理区吸湿、再生区加热脱附,两股气流分开走,干燥风可连续循环,不必频繁换料。
The honeycomb rotor is zoned with a process sector adsorbing and a regeneration sector desorbing, the two air streams kept apart so drying air recirculates without frequent changes.

结构与控制 / Structure & Control

干燥料斗带保温层与视料窗,热风从锥底进入、上部分布板均流;露点表实时显示,超限报警提示查料斗密封与转轮。
The insulated hopper has a sight window, hot air enters at the cone base and a distributor evens the flow, and a live dew point gauge alarms on seal or rotor problems.

运行与精度 / Performance & Accuracy

PETG 常见干燥条件 65 到 70℃、四小时以上,PLA 更怕高温,取 55 到 60℃ 长时间干;露点稳定在 -40℃ 以下再开挤出。
PETG commonly dries at 65 to 70 C for four hours or more, while PLA prefers 55 to 60 C for longer; extrusion starts once dew point holds below minus 40 C.

操作与维护 / Operation & Maintenance

每班看露点与料位,每周清料斗内壁,再生加热器积碳会推高露点,按季度检查清理;过滤器按压差换,不等露点漂。
Check dew point and level each shift, clean the hopper wall weekly, inspect the regeneration heater quarterly since carbon raises dew point, and change filters on differential pressure.

参数速览 / Specifications

型号 TCD-300|干燥风量 300 立方米每小时|露点 -40℃ 以下|料斗 100~400 升|控制 PID 配露点显示
Model TCD-300 | 300 m3/h drying air | Dew point below minus 40 C | 100-400 litre hopper | PID control with dew point display

应用场景 / Applications

PETG 与 PLA 耗材线的前处理、PA 与 PC 高温料干燥、再生切片掺混前的除湿、挤出前机边补干。
Pre-treatment on PETG and PLA filament lines, drying PA and PC, dehumidifying ahead of regrind blending, and dry top-up beside extruders.

选型与交付 / Sizing & Delivery

给出线径、色数、色段长度与小时产量四项即可出选型计算书,确认配置与产能;签约后按交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send diameter, colour count, band length and hourly output for a sizing sheet that confirms configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.

常见问题 / FAQ

Q:露点是不是越低越好?
Q: Is a lower dew point always better?
A:够用就行。PETG 与 PLA 在 -40℃ 已满足多数工艺,追到 -50℃ 以下只会拉高再生能耗与转轮损耗。
Enough is enough. PETG and PLA are usually fine at minus 40 C, and pushing below minus 50 C only raises regeneration energy and rotor wear.

Q:干燥没问题还是冒泡怎么办?
Q: Still bubbling with drying under control?
A:查输送段是否回潮、料斗密封是否漏气,再查挤出温度是否过高导致降解产气;别只盯露点。
Check re-absorption in conveying and hopper seals, then whether melt temperature is high enough to degrade the resin; do not look only at dew point.

相关产品 / Related Products

PET结晶干燥系统

粤公网安备 44190002002288号