产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
深圳3D打印彩虹线收卷牵引段 TWD-60|张力排线整齐

深圳3D打印彩虹线收卷牵引段 TWD-60|张力排线整齐
Winding and Haul-Off Section TWD-60 for Filament
收卷欠佳常被当成小事,其实线材压线、松卷、层间粘连,客户开卷就断,问题会被算到整条线上。
Poor winding looks minor until the customer unwinds a spool: crushed layers, slack coils and sticking strands break on opening and the whole line takes the blame.
设备说明 / Equipment Overview
牵引用伺服驱动,速度跟随测径信号微调;张力由浮动辊或 dancer 反馈,收卷从空盘到满盘张力变化被拉平。
The haul-off runs on servo drive trimmed by the gauging signal, tension comes from a dancer roller, and the change from empty to full spool is flattened out.
结构与控制 / Structure & Control
排线装置按线径与盘宽设定行程与换向点,边缘留 2 到 3 毫米余量;排线速度与收卷转速联动,避免叠线。
The traversing unit takes stroke and reversal points from strand diameter and spool width with a 2 to 3 mm margin, and its speed interlocks with spool rotation to prevent overlap.
运行与精度 / Performance & Accuracy
线径 1.75 毫米、公差正负 0.02 毫米时,张力波动要控在较小范围;张力过大线材被拉细,过小则松卷,按实测线径反推设定。
At 1.75 mm within plus or minus 0.02 mm, tension must stay tight: too much thins the strand, too little gives slack spools, so set it from measured diameter.
操作与维护 / Operation & Maintenance
每班检查导轮与排线滑块磨损,导轮积料会划伤线材表面;换盘时先降速再换轴,避免瞬间张力冲击拉断。
Check guide rollers and traversing sliders each shift since build-up scores the surface, and slow down before changing a spool so the tension shock does not snap the strand.
参数速览 / Specifications
型号 TWD-60|牵引 伺服驱动|收卷 张力闭环配排线|线径 1.75 与 2.85 mm|盘宽 按客户规格|控制 与测径信号联动
Model TWD-60 | Servo haul-off | Closed-loop tension with traversing | 1.75 and 2.85 mm | Spool width to customer spec | Interlocked with gauging
应用场景 / Applications
彩虹渐变线与单色线的收卷、多色小盘打样、再生料线的收卷改造、旧线加装张力与排线。
Winding for gradient and single-colour filament, small multi-colour sample spools, retrofits on regrind lines, and adding tension and traversing to older lines.
选型与交付 / Sizing & Delivery
给出线径、色数、色段长度与小时产量四项即可出选型计算书,确认配置与产能;签约后按交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send diameter, colour count, band length and hourly output for a sizing sheet that confirms configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.
常见问题 / FAQ
Q:收卷不齐是排线还是张力问题?
Q: Is untidy winding traversing or tension?
A:看边缘:整盘边缘呈波浪多为排线换向点不准,整盘松紧不一多为张力波动,两者常同时存在。
Read the edges: wavy edges mean reversal points are off, while uneven tightness means tension swings, and both often appear together.
Q:能不能只加装收卷段?
Q: Can the winding section be added alone?
A:可以,旧线加装牵引与张力收卷是常见改造,接口按现有挤出与测径信号对接,不必换主机。
Yes, adding haul-off with tension winding to an existing line is common, interfacing to the current extrusion and gauging signals without changing the extruder.
