产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

上海PET拉丝干燥设备 TPD-800

日期:2026-11-20 14:05
浏览次数:34
摘要:上海PET拉丝干燥设备 TPD-800 PET Filament Drying Line TPD-800 for Shanghai 上海PET拉丝干燥设备 TPD-800(PET Filament Drying Line TPD-800):结晶、除湿、干燥三段一体,切片从进料到出料一路走完,露点稳定

PET拉丝干燥设备 TPD-800 整机 纯白底图

上海PET拉丝干燥设备 TPD-800
PET Filament Drying Line TPD-800 for Shanghai

上海PET拉丝干燥设备 TPD-800(PET Filament Drying Line TPD-800):结晶、除湿、干燥三段一体,切片从进料到出料一路走完,露点稳定、含水率可控。
PET Filament Drying Line TPD-800 for Shanghai: Crystallising, dehumidifying and drying run as one line, so chips go from feed to outlet with stable dew point and controlled moisture.

设备说明 / Equipment Overview

三段串联:结晶罐先把切片软化点提上来,除湿主机把露点压到 -40℃ 以下,末段干燥料斗完成均温均湿。
Three stages in series: the crystalliser raises the softening point, the dryer pushes dew point below -40 C, and the final hopper equalises temperature and moisture.

结构与控制 / Structure & Control

各段独立控温,PLC 记录露点、料位与产量;输送用负压管路,避免切片在输送段吸水回潮。
Each stage holds its own temperature and the PLC logs dew point, level and output; vacuum conveying keeps chips from re-absorbing moisture in transit.

运行与精度 / Performance & Accuracy

按产量与切片规格匹配停留时间,含水率常见控制目标 50 ppm 以下;再生料含水高时降低单段产量保质量。
Residence time follows output and chip size, with moisture targets commonly under 50 ppm; wet regrind means running lower throughput to hold quality.

操作与维护 / Operation & Maintenance

每班查露点与料位,每周清结晶罐与料斗;转轮与过滤器按压差更换,别等露点漂了再处理。
Check dew point and level each shift, clean vessel and hopper weekly, and change rotor filters on differential pressure rather than after dew point drifts.

参数速览 / Specifications

型号 TPD-800|产能 800 kg/h|三段 结晶+除湿+干燥|露点 -40~-60℃|控制 PLC 全流程记录
Model TPD-800 | 800 kg/h | Three stages | Dew point -40 to -60 C | PLC with full-process logging

应用场景 / Applications

涤纶与丙纶长丝、短纤与拉丝线、瓶片与再生切片纺丝、单丝与扁丝生产前处理。
Polyester and polypropylene filament, staple and drawing lines, bottle flake and reclaimed chip spinning, monofilament and tape yarn preparation.

上海配套 / Local Support in Shanghai

包装、医疗与精密件为主,车间恒温、场地租金高,倾向占地小、自动化程度高的配置。
Packaging, medical and precision parts in climate-controlled, expensive floor space, favouring compact automated units.

选型与交付 / Sizing & Delivery

提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.

常见问题 / FAQ

Q:再生料能不能直接上这条线?
Q: Can regrind run straight on this line?
A:可以,但再生料含水与粉末偏高,建议前置筛分并下调单段产量;混用比例高时把结晶段温度适当提高。
Yes, but regrind carries more moisture and fines: screen ahead, lower throughput and raise the crystalliser temperature at high blend ratios.

Q:露点合格但丝还是断怎么办?
Q: Dew point is fine but the yarn still breaks?
A:先查输送段是否回潮与料斗密封,再看喷丝板温度与组件压力;干燥只是其中一环,别只盯露点。
Check re-absorption in conveying and hopper seals, then spinneret temperature and pack pressure; drying is only one link.

上海 本地配套与选型提示 / Local Notes for 上海

汽车、医疗与包装并重,认证要求多,认证场景留存每批重量记录便于追溯,设备材质与清洁流程按客户体系走。
Local industry sets the material mix in 上海, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:PET 动态干燥机。
Model and configuration: PET 动态干燥机.

相关产品 / Related Products

相关阅读 / Related Reading

TPD 系列的配置与双塔选配

TPD 系列按每小时处理量分档,TPD-800 对应中等产能的拉丝线,料斗容积、结晶段加热功率与除湿风量按产能配套。现场常见两种配置:单塔除湿满足常规拉丝与短纤,双塔除湿用于连续运转、露点要求更低的纺丝与细旦产线。

选双塔时要一起看三件事:一是再生加热源,电加热投入低、运行成本高,有余热的车间可接余热;二是切换阀的耐温与密封,阀件泄漏会让露点在切换瞬间上抬;三是控制逻辑,吸附与再生周期按实测露点曲线设定,比按固定时间切换更省能耗。

设备落地后建议把露点、料斗温度、下料速度三项做联动记录,跑一周就能看出本厂原料的合适参数区间,后续换批次原料时不用重新试。

粤公网安备 44190002002288号