产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

无锡PET拉丝干燥设备 TPD-800

日期:2026-11-21 00:54
浏览次数:26
摘要:无锡PET拉丝干燥设备 TPD-800 PET Filament Drying Line TPD-800 for Wuxi 无锡PET拉丝干燥设备 TPD-800(PET Filament Drying Line TPD-800):结晶、除湿、干燥三段一体,切片从进料到出料一路走完,露点稳定、含水率

PET拉丝干燥设备 TPD-800 整机 纯白底图

无锡PET拉丝干燥设备 TPD-800
PET Filament Drying Line TPD-800 for Wuxi

无锡PET拉丝干燥设备 TPD-800(PET Filament Drying Line TPD-800):结晶、除湿、干燥三段一体,切片从进料到出料一路走完,露点稳定、含水率可控。
PET Filament Drying Line TPD-800 for Wuxi: Crystallising, dehumidifying and drying run as one line, so chips go from feed to outlet with stable dew point and controlled moisture.

设备说明 / Equipment Overview

三段串联:结晶罐先把切片软化点提上来,除湿主机把露点压到 -40℃ 以下,末段干燥料斗完成均温均湿。
Three stages in series: the crystalliser raises the softening point, the dryer pushes dew point below -40 C, and the final hopper equalises temperature and moisture.

结构与控制 / Structure & Control

各段独立控温,PLC 记录露点、料位与产量;输送用负压管路,避免切片在输送段吸水回潮。
Each stage holds its own temperature and the PLC logs dew point, level and output; vacuum conveying keeps chips from re-absorbing moisture in transit.

运行与精度 / Performance & Accuracy

按产量与切片规格匹配停留时间,含水率常见控制目标 50 ppm 以下;再生料含水高时降低单段产量保质量。
Residence time follows output and chip size, with moisture targets commonly under 50 ppm; wet regrind means running lower throughput to hold quality.

操作与维护 / Operation & Maintenance

每班查露点与料位,每周清结晶罐与料斗;转轮与过滤器按压差更换,别等露点漂了再处理。
Check dew point and level each shift, clean vessel and hopper weekly, and change rotor filters on differential pressure rather than after dew point drifts.

参数速览 / Specifications

型号 TPD-800|产能 800 kg/h|三段 结晶+除湿+干燥|露点 -40~-60℃|控制 PLC 全流程记录
Model TPD-800 | 800 kg/h | Three stages | Dew point -40 to -60 C | PLC with full-process logging

应用场景 / Applications

涤纶与丙纶长丝、短纤与拉丝线、瓶片与再生切片纺丝、单丝与扁丝生产前处理。
Polyester and polypropylene filament, staple and drawing lines, bottle flake and reclaimed chip spinning, monofilament and tape yarn preparation.

无锡配套 / Local Support in Wuxi

薄膜、片材与化纤配套集中,产线速度快、料性偏新料,对连续稳定与数据记录有要求。
Film, sheet and fibre concentrate here at high line speeds with mostly virgin material, so continuous stability and data logging matter.

选型与交付 / Sizing & Delivery

提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.

常见问题 / FAQ

Q:再生料能不能直接上这条线?
Q: Can regrind run straight on this line?
A:可以,但再生料含水与粉末偏高,建议前置筛分并下调单段产量;混用比例高时把结晶段温度适当提高。
Yes, but regrind carries more moisture and fines: screen ahead, lower throughput and raise the crystalliser temperature at high blend ratios.

Q:露点合格但丝还是断怎么办?
Q: Dew point is fine but the yarn still breaks?
A:先查输送段是否回潮与料斗密封,再看喷丝板温度与组件压力;干燥只是其中一环,别只盯露点。
Check re-absorption in conveying and hopper seals, then spinneret temperature and pack pressure; drying is only one link.

无锡 本地配套与选型提示 / Local Notes for 无锡

精密注塑、光伏与电子配套集中,精密件把称量精度做到 ±0.1%,回料组加装料位与温度检测。
Local industry sets the material mix in 无锡, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:PET 动态干燥机。
Model and configuration: PET 动态干燥机.

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号