产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

武汉除湿干燥机 TCD-300

日期:2026-11-21 03:32
浏览次数:36
摘要:武汉除湿干燥机 TCD-300 Dehumidifying Dryer TCD-300 for Wuhan 武汉除湿干燥机 TCD-300(Dehumidifying Dryer TCD-300):蜂巢转轮除湿配干燥料斗,露点稳定在 -40℃ 以下,吸湿性料在连续干燥中不易回潮。 Dehumidif

除湿干燥机 TCD-300 整机 纯白底图

武汉除湿干燥机 TCD-300
Dehumidifying Dryer TCD-300 for Wuhan

武汉除湿干燥机 TCD-300(Dehumidifying Dryer TCD-300):蜂巢转轮除湿配干燥料斗,露点稳定在 -40℃ 以下,吸湿性料在连续干燥中不易回潮。
Dehumidifying Dryer TCD-300 for Wuhan: A honeycomb rotor and drying hopper hold dew point below -40 C, so hygroscopic material stays dry through continuous running.

设备说明 / Equipment Overview

转轮分区除湿:处理区吸湿、再生区加热脱附,两股气流分开走,干燥风可连续循环而不必换料。
The rotor is zoned: the process sector adsorbs moisture while the regeneration sector is heated to desorb it, so drying air recirculates continuously.

结构与控制 / Structure & Control

干燥料斗带保温层与视料窗,热风从锥底进入、上部分布板均流;主机与料斗可分置,多料斗共用一台除湿主机。
The insulated hopper has a sight window, hot air enters at the cone base and a distributor evens the flow, and one dryer can serve several hoppers.

运行与精度 / Performance & Accuracy

按回风温度与露点闭环调节再生温度,避免过度再生浪费电;露点表实时显示,超限报警提醒查料斗密封。
Regeneration temperature is closed-loop on return-air temperature and dew point, waste from over-regeneration is avoided, and a dew-point gauge alarms on hopper seal problems.

操作与维护 / Operation & Maintenance

每班检查再生过滤器与转轮积粉,每月清料斗内壁;再生加热器积碳会导致露点上升,按季度检查并清理。
Check the regeneration filter and rotor dust each shift, clean the hopper wall monthly, and inspect the regeneration heater quarterly since carbon build-up lifts dew point.

参数速览 / Specifications

型号 TCD-300|干燥风量 300 m³/h|露点 ≤-40℃|料斗 100~400 kg|控制 PID 配露点显示
Model TCD-300 | 300 m3/h drying air | Dew point below -40 C | 100-400 kg hopper | PID control with dew-point display

应用场景 / Applications

PET、PA、PC、ABS 等吸湿性料的干燥,瓶坯与片材线、纺丝与改性造粒、精密注塑前处理。
Drying hygroscopic PET, PA, PC and ABS for bottle and sheet lines, spinning and compounding, and precision molding.

武汉配套 / Local Support in Wuhan

汽车与光电子配套,注塑挤出并存,产线节拍快,干燥与供料要求连续稳定。
Automotive and optoelectronics work with fast takt times, where drying and feeding must stay continuous.

选型与交付 / Sizing & Delivery

提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.

常见问题 / FAQ

Q:露点是不是越低越好?
Q: Is a lower dew point always better?
A:看料性与工艺:PET 一般 -40℃ 够用,部分工程塑料需 -50℃ 以下;盲目追低露点会拉高再生能耗与转轮损耗。
It depends: PET is fine at -40 C while some engineering resins need below -50 C. Chasing lower figures raises regeneration energy and rotor wear.

Q:干燥不均匀怎么查?
Q: How to check uneven drying?
A:先看风量分配板是否堵、料斗是否偏流,再看回风温度与露点是否漂;料位过低也会短路,保持料位在视窗中线以上。
Check the distributor and hopper channelling first, then return-air temperature and dew point. A low level short-circuits the airflow, so keep it above the window centre.

武汉 本地配套与选型提示 / Local Notes for 武汉

汽车与电子并重,件重跨度大,件重跨度大时称量斗容积按上限选,小件时用低量程段确保分辨率。
Local industry sets the material mix in 武汉, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; component count and weighing range are quoted against the actual job.

对应机型与配置见站内产品页:新型 PET 动态除湿干燥机。
Model and configuration: 新型 PET 动态除湿干燥机.

相关产品 / Related Products

相关阅读 / Related Reading

粤公网安备 44190002002288号