产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

Gravimetric Dosing & Blending System 挤出在线称重混配系统

日期:2026-11-20 17:14
浏览次数:25
摘要:Gravimetric Dosing & Blending System 挤出在线称重混配系统 Gravimetric Blender TGB-4 for China nationwide Gravimetric Dosing & Blending System 挤出在线称重混配系统(Gravime

称重式混料机 TGB-4 整机 纯白底图

Gravimetric Dosing & Blending System 挤出在线称重混配系统
Gravimetric Blender TGB-4 for China nationwide

Gravimetric Dosing & Blending System 挤出在线称重混配系统(Gravimetric Blender TGB-4):四组份独立称重,新料、回料、色母与助剂分别计量后混匀,配比按配方号调用。
Gravimetric Blender TGB-4 for China nationwide: Four components are weighed independently, then blended to a recipe number instead of by volume.

设备说明 / Equipment Overview

按重量逐组下料,称重斗累计到单批总重才放料,比例跟着配方走;四组覆盖多数注塑与挤出场景,五六组按需加装。
Each component discharges by weight and the batch drops at the target total, so the ratio follows the recipe. Four components cover most jobs; five or six can be added.

结构与控制 / Structure & Control

称重传感器、下料螺杆、搅拌腔与触摸屏电控装成一机,换料号即调配方号;末组补差,整批误差收在末组。
Load cell, dosing screws, mixing chamber and touch panel sit in one frame; a material change is a recipe change, with the last component making up the balance.

运行与精度 / Performance & Accuracy

每批记录实际重量并存入配方,回料比例波动时自动跟随设定值;可选 Modbus 接口接上位机,多机台集中看数据。
Batch weight is logged against the recipe and the set point is followed when regrind ratio drifts. An optional Modbus port feeds multi-machine monitoring.

操作与维护 / Operation & Maintenance

每班清称重斗与搅拌腔残留,定期校传感器零点;换料号时清下料口,避免颜色交叉。
Clear the hopper and chamber each shift and verify load-cell zero periodically; a material change needs the dosing ports cleaned to avoid colour cross-over.

参数速览 / Specifications

型号 TGB-4|组份 4 组(可扩至 6)|处理量 50~3000 kg/h|计量 增重式逐组称量|控制 触摸屏(可选 Modbus)
Model TGB-4 | 4 components (6 optional) | 50-3000 kg/h | Gain-in-weight dosing | Touch panel with Modbus option

应用场景 / Applications

注塑机边配比、挤出片材与型材、吹膜与流延、管材生产,以及破碎料按比例掺混;单机对应一台用料设备,多机台可集中管理。
Blending beside injection presses, sheet and profile extrusion, blown film and casting, pipe lines, and ratio-controlled regrind use.

华南与国内配套 / Local Support in China nationwide

按客户产线与料性配型,可配合整线交付;常用件与耗材常年备货,远程与到场两种支持方式并行。
Configured to the line and material, deliverable as a package; common parts stay in stock with both remote and on-site support.

3D 打印耗材挤出配比 / Dosing for 3D Printing Filament

3D 打印线材(PLA、PETG、ABS、TPU)对线径与色差敏感,配比端要的是稳定而非流量:1.75 mm 下线径 ±0.03 mm 的跳动,源头多在配比漂移而不在模头。把新料、色母、增韧剂、抗静电剂分开称量,单组误差不叠加,线径曲线才平;TPU 软料则要压低回料、减小剪切,单组失重式喂料比整机混料更稳。
Filament tolerances follow dosing stability rather than throughput: at 1.75 mm a plus or minus 0.03 mm swing usually starts at the blender, not the die. Weighing virgin, masterbatch, impact modifier and antistatic apart keeps errors from stacking, while soft TPU wants low regrind and gentle shear, where a single loss-in-weight feeder beats a full blender.

彩虹分层拉丝 / Rainbow Layer Extrusion

彩虹色拉丝靠多台挤出机同时供料、按层换色,配比端要满足两点:各色通道响应一致,换色残料清得净。六组份可为每色单开一组,切换走配方调用,过渡段通常压到 20~40 米;再按组错峰补料、让闭环跟挤出产量联动,彩条边界才整齐。
Rainbow filament runs several extruders at once and switches colour by layer, so the dosing side needs matched response across colour channels and clean purging at change. A six-component unit gives each colour its own loop switched by recipe, holding transitions near 20-40 metres; staggered refill tied to extruder throughput keeps the boundaries even.

选型与交付 / Sizing & Delivery

提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.

常见问题 / FAQ

Q:四组份够不够用?
Q: Are four components enough?
A:新料、回料、色母加一组助剂是常见配置。若同时用两种色母或两种助剂,选六组更省事。
Virgin, regrind, masterbatch and one additive is the usual set; two of either makes six components easier.

Q:称重式比体积式好在哪?
Q: Why gravimetric rather than volumetric?
A:体积式受颗粒间隙、料位与回料堆密度影响,比例会漂;称重式按实际重量结算,回料占比大时差别更明显。
Volumetric dosing drifts with granule gaps, hopper level and regrind density; gravimetric settles on actual weight, and the gap widens with high regrind shares.

选型与验收要点 / Sizing and Acceptance Checklist

选型先定三件事:单批总重、组份数量、添加量下限。单批总重决定称量斗容积,组份数量决定机型组数,添加量下限决定要不要上微型螺杆。


相关阅读 / Related Reading

称重式混料机

粤公网安备 44190002002288号