产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

塑料除湿干燥机 温州 TCD-1200|Plastic Desiccant Dryer / Dehumidifying Dryer

日期:2026-11-19 10:55
浏览次数:0
摘要:温州眼镜、鞋材与注塑集群,露点 -25~-30 ℃,料斗 120 kg。中英文对照说明结构与参数。

温州塑料除湿干燥机 TCD-1200

温州塑料除湿干燥机 TCD-1200|Plastic Desiccant Dryer TCD-1200

适用于温州的眼镜、鞋材与注塑集群。设备按料斗容积 120 kg、风量约 160 m³/h、露点 -25~-30 ℃ 的配置供货,可配机边或集中两种安装方式。

Built for the eyewear, footwear and injection cluster in 温州, supplied with a 120 kg hopper, about 160 m³/h airflow and a dew point of -25~-30 °C, for machine-side or central installation.

这一条重点讲:料斗干燥与除湿联动

Focus of this page: Drying time depends on layer thickness, air temperature and airflow together; fix the air path before the temperature

干燥时间由料层厚度、风温和风量共同决定,先把风路理顺再谈温度设定。在温州一带的车间,风量与料斗容积要随机台吨位一起定。

Drying time depends on layer thickness, air temperature and airflow together; fix the air path before the temperature. In workshops like those in 温州, the airflow and hopper figure is set together with the machine tonnage.

结构与参数 / Structure and figures

蜂巢转轮除湿 + 电加热料斗 + 闭环风路;露点 -25~-30 ℃、料斗 120 kg、风量 160 m³/h、再生加热 120~160 ℃ 可调;料温上限按原料牌号设定,一般不超过 120 ℃。

Honeycomb wheel dehumidifying, electrical hopper heating and a closed-loop air path: dew point -25~-30 °C, hopper 120 kg, airflow 160 m³/h, regeneration 120-160 °C adjustable, material temperature normally kept under 120 °C.

接口为单相/三相可选,控制面板带露点显示与超温报警,料位不足时自动提示补料。

Single or three-phase supply, dew-point readout and over-temperature alarm on the panel, with a low-level refill prompt.

交货与调试:温州及周边可上门安装调试,随机提供中文/英文操作说明与常见故障对照表。

Delivery: installation and commissioning are available in 温州 and nearby areas, with Chinese/English manuals and a fault cross-reference table.

粤公网安备 44190002002288号