产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
杭州3D打印耗材双色渐变喂料机 TGB-2F|两路同步配比
杭州3D打印耗材双色渐变喂料机 TGB-2F|两路同步配比
Two-Colour Gradient Feeder TGB-2F
双色的难点不在配色,而在两路响应要一致:基料与色母的螺杆直径差一倍,转速同步了流量也不一定同步。
Dual colour is less about the recipe than matched response: the base and masterbatch screws differ in diameter, so equal speed does not mean equal flow.
设备说明 / Equipment Overview
两路各配计量螺杆与驱动,基料走大螺杆、色母走小螺杆,按流量比而不是转速比设定,换算成克数更直观。
Each loop has its own screw and drive, a large one for base and a small one for masterbatch, set by flow ratio rather than speed ratio so grams read directly.
结构与控制 / Structure & Control
两路出料在混料座汇合,拌料器做短程混匀,避免色母颗粒在进料口局部富集形成色点;混料座可拆,清料方便。
The streams meet in a mixing seat with a short stirrer so masterbatch does not concentrate at the throat and form colour specks, and the seat removes for cleaning.
运行与精度 / Performance & Accuracy
渐变由色母流量按时间递增或递减实现,基料流量保持恒定;双色丝绸线的过渡段常见 20 到 40 米,靠线速与流量曲线配合。
Gradients come from ramping masterbatch flow up or down while base flow holds steady; silk filament transitions commonly run 20 to 40 metres, set by line speed and the flow ramp.
操作与维护 / Operation & Maintenance
换色清混料座与色母小螺杆即可,基料侧不必拆;色母受潮会结块,换料前先确认干燥状态再上机。
A colour change only clears the mixing seat and the small masterbatch screw, not the base side; masterbatch absorbs moisture and cakes, so check its drying state before loading.
参数速览 / Specifications
型号 TGB-2F|组份 2 组|产量 3~20 kg/h|计量 增重式逐组称量|驱动 计量电机 2 台|控制 触控屏 流量曲线设定
Model TGB-2F | 2 components | 3-20 kg/h | Gain-in-weight per loop | Two metering drives | Touch panel with flow ramp setting
应用场景 / Applications
双色丝绸线、双色互融文创耗材、本色加单色母的功能线、实验室两料配比试验。
Dual-colour silk filament, dual-colour creative consumables, natural resin with one functional masterbatch, and two-material laboratory trials.
选型与交付 / Sizing & Delivery
给出线径、色数、色段长度与小时产量四项即可出选型计算书,确认配置与产能;签约后按交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send diameter, colour count, band length and hourly output for a sizing sheet that confirms configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.
常见问题 / FAQ
Q:双色能不能做三层?
Q: Can two colours make three layers?
A:两路只能做两色或两料;要三层结构需要三路以上,或者用两台挤出机共挤再配两路喂料。
Two loops give two colours or two materials; a three-layer structure needs three loops or two extruders co-extruding with two feeding loops.
Q:色母比例很低时怎么配比?
Q: How to dose a very low masterbatch share?
A:换小直径螺杆比降转速更稳,转速太低时螺杆每转的输送量不稳定,比例反而会漂。
A smaller screw beats slowing the drive; at very low speed the per-turn output becomes unstable and the ratio drifts.
