产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
Gravimetric Blender for Pipe & Profile 管材型材称重混料机 TGB-4
Gravimetric Blender for Pipe & Profile 管材型材称重混料机 TGB-4
Gravimetric Blender for Pipe & Profile TGB-4
Gravimetric Blender for Pipe & Profile 管材型材称重混料机 TGB-4:四组份独立称重,新料、回料、色母与助剂分别计量后混匀,配比按配方号调用。
Gravimetric Blender for Pipe & Profile TGB-4: Four components are weighed independently, then blended to a recipe number instead of by volume.
设备说明 / Equipment Overview
按重量逐组下料,称重斗累计到单批总重才放料,比例跟着配方走;四组覆盖多数注塑与挤出场景,五六组按需加装。
Each component discharges by weight and the batch drops at the target total, so the ratio follows the recipe. Four components cover most jobs; five or six can be added.
管材与型材线产量大,配比一旦漂,壁厚与米重立刻变;这类线建议配产量反馈,把 kg/h 与米重一起看。
Pipe and profile lines run high output, and any ratio drift shows up at once in wall thickness and metre weight; add throughput feedback and read kg/h against metre weight.
结构与控制 / Structure & Control
称重传感器、下料螺杆、搅拌腔与触摸屏电控装成一机,换料号即调配方号;末组补差,整批误差收在末组。
Load cell, dosing screws, mixing chamber and touch panel sit in one frame; a material change is a recipe change, with the last component making up the balance.
运行与精度 / Performance & Accuracy
每批记录实际重量并存入配方,回料比例波动时自动跟随设定值;可选 Modbus 接口接上位机,多机台集中看数据。
Batch weight is logged against the recipe and the set point is followed when regrind ratio drifts. An optional Modbus port feeds multi-machine monitoring.
操作与维护 / Operation & Maintenance
每班清称重斗与搅拌腔残留,定期校传感器零点;换料号时清下料口,避免颜色交叉。
Clear the hopper and chamber each shift and verify load-cell zero periodically; a material change needs the dosing ports cleaned to avoid colour cross-over.
参数速览 / Specifications
型号 TGB-4|组份 4 组|处理量 100~3000 kg/h|安装 挤出线上方|控制 触摸屏(可选 Modbus)
Model TGB-4 | 4 components | 100-3000 kg/h | Above the extruder | Touch panel, Modbus optional
应用场景 / Applications
注塑机边配比、挤出片材与型材、吹膜与流延、管材生产,以及破碎料按比例掺混;单机对应一台用料设备,多机台可集中管理。
Blending beside injection presses, sheet and profile extrusion, blown film and casting, pipe lines, and ratio-controlled regrind use.
开机料多的产线可在混料段加旁路,先走直通再切混配,减少开机段的废料。
Lines with a lot of start-up scrap can bypass the blender until the line stabilises, cutting waste in the start-up phase.
命名与叫法 / Naming Note
英文资料里常见多种写法,选型以参数为准,不以叫法为准;中文侧常见称重式混料机、称重式拌料机、计量混配机,港台多用拌料机。
English sources use several names for the same machine; size on parameters, not on the label. Chinese buyers say 混料机 or 拌料机, with 拌料机 common in Hong Kong and Taiwan.
选型与交付 / Sizing & Delivery
提供物料清单、单班产量与料性后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附中英文手册与备件清单。
Send the material list, output per shift and material behaviour and we return a sizing sheet; after order we ship on schedule, install, commission and train, with bilingual manual and spare list.
常见问题 / FAQ
Q:四组份够不够用?
Q: Are four components enough?
A:新料、回料、色母加一组助剂是常见配置。若同时用两种色母或两种助剂,选六组更省事。
Virgin, regrind, masterbatch and one additive is the usual set; two of either makes six components easier.
Q:称重式比体积式好在哪?
Q: Why gravimetric rather than volumetric?
A:体积式受颗粒间隙、料位与回料堆密度影响,比例会漂;称重式按实际重量结算,回料占比大时差别更明显。
Volumetric dosing drifts with granule gaps, hopper level and regrind density; gravimetric settles on actual weight, and the gap widens with high regrind shares.
当地 本地配套与选型提示 / Local Notes for 当地
当地塑料加工以注塑与挤出为主,组份数量与称量范围按实际料号与回料比例确定。
Local industry sets the material mix in 当地, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:Gravimetric Blender 重力式称重混料机。
Model and configuration: Gravimetric Blender 重力式称重混料机.
