产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
绍兴PET搅拌结晶机 T3000J

绍兴PET搅拌结晶机 T3000J
PET Mixing Crystallizer T3000J for Shaoxing
绍兴PET搅拌结晶机 T3000J(PET Mixing Crystallizer T3000J):搅动加热让切片在罐内持续翻动,结晶均匀、不粘连,出料后直接进干燥料斗。
PET Mixing Crystallizer T3000J for Shaoxing: Stirred heating keeps chips moving inside the vessel so crystallisation stays even and free of agglomeration, ready to feed the drying hopper.
设备说明 / Equipment Overview
PET 切片直接升温干燥容易粘连结块,先做搅拌结晶把软化点提上来,后续除湿干燥与输送才顺畅。
Heating PET chips straight into drying makes them stick and lump, so stirred crystallisation raises the softening point first and keeps drying and conveying smooth.
结构与控制 / Structure & Control
T3000J 罐内搅拌轴变频调速,热风从罐底送入形成循环,切片持续翻动、避免局部过热;出料温度可控,可直接进干燥料斗。
The T3000J drives a variable-speed shaft in the vessel while hot air enters at the base and circulates, so chips keep turning and no local hot spot forms. Outlet temperature is controlled for direct transfer to the dryer.
运行与精度 / Performance & Accuracy
按料位与温度双条件控制,批次结束给出提示;可与除湿干燥机、中央供料按顺序联动,结晶—干燥—输送一条线走通。
Control watches both level and temperature and signals at batch end. It interlocks with the dehumidifying dryer and central conveying, so crystallising, drying and conveying run as one line.
操作与维护 / Operation & Maintenance
搅拌轴与罐体按物料磨蚀性选材,密封件耐温;再生切片含粉多时前置筛分,减少罐内积料与清理频次。
Shaft and vessel materials follow the abrasiveness of the material and seals are heat-rated. Screening ahead of the vessel keeps powder from building up when regrind is dusty.
参数速览 / Specifications
型号 T3000J|单批 300~3000 kg|加热 电加热配热风循环|搅拌 变频调速|控制 温度与料位联动
Model T3000J | 300-3000 kg per batch | Electric heating with hot-air circulation | Variable-speed stirring | Interlocked temperature and level control
应用场景 / Applications
瓶坯与片材级 PET 前处理、再生切片造粒前结晶、纺丝级切片预处理、PLA 与工程塑料改性前的配料干燥。
Pre-treatment for bottle and sheet grade PET, crystallising before reclaim pelletising, spinning-grade chip preparation, and compounding lines for PLA and engineering plastics.
薄膜与涤纶线对粉末敏感,回料段建议加筛分与除粉,减少晶点与断膜。
Film and polyester lines are powder sensitive, so screen and de-dust the regrind path to limit gels and breaks.
绍兴地区配套 / Local Supply in Shaoxing
涤纶、薄膜与包装印刷配套集中,料性与膜级要求高,回料按比例掺用,对配比一致性与粉末控制要求突出。
Shaoxing concentrates polyester, film and packaging print, where material grades and film quality are demanding and regrind is blended by ratio, making consistency and dust control critical.
选型与交付 / Sizing & Delivery
提供物料清单与产线节拍后出具选型计算书,确认组份与处理量;签约后按约定交期发运,到场完成安装、联动调试与操作培训,随机附操作手册与备件清单。
Send the material list and line takt time and we return a sizing sheet confirming configuration and throughput. After order we ship on the agreed date, install, commission and train on site, with the manual and spare list.
常见问题 / FAQ
Q:结晶和干燥能不能一步做?
Q: Can crystallising and drying be one step?
A:多数 PET 工艺要先结晶再除湿干燥。合并做容易结块,再生料含水高时更明显。
Most PET processes crystallise first, then dry with dehumidified air. Combining them invites lumping, especially with wet regrind.
Q:搅拌转速怎么定?
Q: How is the stirring speed set?
A:按切片规格与批量定:转速过低翻动不足会局部过热,过高则增加粉末与磨损,建议按实际物料试一次再定参数。
Set by chip size and batch weight: too slow leaves dead zones and local overheating, too fast adds fines and wear. Run one trial on the actual material before fixing the parameter.
绍兴 本地配套与选型提示 / Local Notes for 绍兴
纺织、化纤与薄膜配套集中,BOPP、CPP 线较多,薄膜线对色差敏感,色母组用独立小螺杆,添加量 0.5% 以下配高频采样。
Local industry sets the material mix in 绍兴, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:PET 片材低速搅拌结晶机。
Model and configuration: PET 片材低速搅拌结晶机.
