产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
台州再生瓶片结晶机 T3000J|筛分除粉防结块

台州再生瓶片结晶机 T3000J|筛分除粉防结块
PET Mixing Crystallizer T3000J for Taizhou
台州再生瓶片结晶机 T3000J|筛分除粉防结块(PET Mixing Crystallizer T3000J):搅动加热让切片在罐内持续翻动,结晶均匀、不粘连,出料直接进干燥料斗。
PET Mixing Crystallizer T3000J for Taizhou: Stirred heating keeps chips moving so crystallisation stays even and free of lumps, ready for the drying hopper.
设备说明 / Equipment Overview
PET 切片直接升温干燥容易粘连结块,先做搅拌结晶把软化点提上来,后续除湿干燥与输送才顺畅。
Heating chips straight into drying makes them lump, so stirred crystallisation raises the softening point first.
结构与控制 / Structure & Control
T3000J 罐内搅拌轴变频调速,热风从罐底送入循环,切片持续翻动、避免局部过热;出料温度可控。
The T3000J drives a variable-speed shaft while hot air enters at the base and circulates, so chips keep turning and no hot spot forms; outlet temperature is controlled.
运行与精度 / Performance & Accuracy
按料位与温度双条件控制,批次结束给出提示;可与除湿干燥机、中央供料按顺序联动,结晶—干燥—输送一条线走通。
Level and temperature jointly control the batch with an end signal, and it interlocks with dryer and conveying for one continuous line.
操作与维护 / Operation & Maintenance
搅拌轴与罐体按物料磨蚀性选材,密封件耐温;再生切片含粉多时前置筛分,减少罐内积料。
Shaft and vessel materials follow abrasiveness, seals are heat-rated, and screening ahead keeps powder out when regrind is dusty.
参数速览 / Specifications
型号 T3000J|单批 300~3000 kg|加热 电加热配热风循环|搅拌 变频调速|控制 温度与料位联动
Model T3000J | 300-3000 kg per batch | Electric heating with air circulation | Variable-speed stirring | Interlocked control
应用场景 / Applications
瓶坯与片材级 PET 前处理、再生切片造粒前结晶、纺丝级切片预处理、PLA 与工程塑料改性前配料。
Bottle and sheet grade PET pre-treatment, crystallising before reclaim pelletising, spinning-grade preparation and compounding.
台州配套 / Local Support in Taizhou
模具与日用品、汽摩配企业密集,中小企业占比高、厂房多租赁,倾向免土建、可移动。
Mold making with daily goods and auto and motorcycle parts, mostly small firms in rented plants preferring movable equipment.
再生瓶片结晶差异 / Reclaim Flake Crystallising
再生瓶片与原生切片不是同一套参数:瓶片带粉末与残留标签,粉尘在结晶段易结团,进料段要加筛分与除粉;含水偏高时先做预干燥再进结晶,结晶温度可上调一档、批量取小,出料更均匀。
Reclaim flake is not virgin chip: powder and label residue clump in the crystallising stage, so screening and de-dusting belong at the inlet; with higher moisture, pre-dry before crystallising, take one step hotter and a smaller batch for even output.
选型与交付 / Sizing & Delivery
提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.
常见问题 / FAQ
Q:结晶和干燥能不能一步做?
Q: Can crystallising and drying be one step?
A:多数 PET 工艺要先结晶再除湿干燥;合并做容易结块,再生料含水高时更明显。
Most processes crystallise first, then dry; combining them invites lumping, especially with wet regrind.
Q:搅拌转速怎么定?
Q: How is the stirring speed set?
A:按切片规格与批量定:过低翻动不足会局部过热,过高增加粉末与磨损,建议按实际料试一次再定。
Set by chip size and batch: too slow overheats locally, too fast adds fines; fix it after one trial.
台州 本地配套与选型提示 / Local Notes for 台州
模具、汽摩配与日用品集中,再生瓶片使用量大,再生瓶片堆密度不稳,结晶干燥前先筛分除粉,混料按增重式结算。
Local industry sets the material mix in 台州, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:PET 结晶干燥机。
Model and configuration: PET 结晶干燥机.
