产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
PET结晶干燥机:结晶、除湿、干燥三段工艺与选型要点

一、为什么 PET 要先结晶再干燥 | Why Crystallize Before Drying
PET 切片和破碎料在 60℃ 以上就开始软化,表面一软,颗粒之间就互相粘连,直接送进干燥塔会在锥斗处架桥、堵料;同时非晶态料在高温高湿环境里容易水解,特性黏度(IV)掉下来,做出的瓶胚或丝强度不够。预结晶的作用是把颗粒表层先晶体化,软化点抬上去,之后才能在 160–180℃ 的干燥温度里自由流动、不结块。
PET chips soften above roughly 60℃. Once the surface softens, pellets stick together, bridge at the cone and block the dryer. Amorphous material also hydrolyses in hot humid air, so intrinsic viscosity drops and the resulting preform or filament loses strength. Pre-crystallisation converts the outer layer into a crystalline skin, raises the softening point and lets the material flow freely at a drying temperature of 160–180℃.
二、三段工艺各有指标,不能合并 | Three Stages, Three Sets of Targets
预结晶解决"粘",一般几分钟到十几分钟,靠热风穿过料层或搅拌桨叶传热;结晶解决"晶体结构",结晶度做到 30%–40%,切片由透明转为乳白;除湿干燥解决"水分",用 −20℃ 至 −40℃ 露点的干空气把表面水和内部水一起带走,瓶胚级通常要求 30ppm 以下,普通注塑件 50ppm 以下。三段各管一件事,跳过预结晶会堵料,跳过除湿只加热会氧化发黄。
Pre-crystallisation solves sticking: a few minutes to about fifteen, driven by hot air through the bed or by agitated paddles. Crystallisation builds structure: crystallinity reaches 30–40% and chips turn from clear to milky. Dehumidified drying removes water: dry air at a dew point of −20 to −40℃ carries away surface and bound moisture, typically below 30 ppm for preform grade and below 50 ppm for general injection. Each stage owns one problem — skip pre-crystallisation and the line blocks; skip dehumidification and simple heating only yellows the material.
三、一体式还是分体式 | Integrated or Split Configuration
一体式搅拌结晶干燥机把结晶与干燥放在同一腔体,搅拌防止粘连,换料清机方便,适合破碎料、片材、多品种小批量;分体式是预结晶器加干燥塔的组合,物料连续走,适合单一品种大产量和瓶胚集中供料。判断口径很直接:产量 800kg/h 以上、品种固定,走分体连续;回料占比高、每日换几次配方,走一体式搅拌。
An integrated agitated crystalliser-dryer keeps crystallising and drying in one chamber; agitation stops agglomeration and cleaning between materials is quick, which suits regrind, sheet and multi-product small batches. The split layout pairs a pre-crystalliser with a drying tower and runs material continuously, which suits a single product at high output and central preform feeding. The rule of thumb: above 800 kg/h with a fixed recipe, go split and continuous; high regrind share with several recipe changes per day, go integrated and agitated.
四、关键参数与常见误判 | Key Parameters and Common Misreads
结晶段温度 160–175℃、停留 15–40 分钟,热风按料层截面风速 0.3–1.0m/s 配风量;干燥段露点 −20 至 −40℃、瓶胚料干燥 4–6 小时,干空气耗量按每公斤料 0.8–1.5m³ 估算。现场较常见的误判是只盯温度表、不看露点表:温度到了,露点却在 0℃ 以上,等于用湿空气烘干,水分始终下不来。
Crystallising runs at 160–175℃ with 15–40 minutes residence, and airflow sized for a face velocity of 0.3–1.0 m/s through the bed. Drying runs at a −20 to −40℃ dew point, four to six hours for preform material, with dry air demand estimated at 0.8–1.5 m³ per kilogram of resin. The usual field mistake is watching the temperature gauge and ignoring the dew point: the setpoint is reached while the dew point sits above 0℃, which means drying with wet air and moisture that never comes down.
五、常见问题与排查 | Troubleshooting
结块架桥——先查预结晶段停留时间与搅拌转速,再看进料是否忽多忽少;IV 下降——查干燥温度是否偏高、露点是否达标、料在塔内是否停留过夜;露点波动——查分子筛再生周期、再生加热与冷却水温度;能耗偏高——查回风比例、塔体保温与料斗是否漏风;出料带粉——查结晶段风速是否过大把细粉吹进过滤器。
Bridging: check residence time and agitator speed in pre-crystallisation, then whether feed rate surges. Falling IV: check drying temperature, dew point and whether material sits in the tower overnight. Dew point swings: check sieve regeneration cycle, regeneration heater and cooling water. High energy: check return-air ratio, tower insulation and hopper leaks. Dust carry-over: check whether crystalliser air velocity is blowing fines into the filter.
六、延伸阅读 | Further Reading
介绍一下PET结晶干燥机;pet结晶干燥机转速;Tpu为什么要结晶还是预防结晶?;如何提高PET的结晶速度?;结晶速度对PET的光学性能有哪些影响?;PET结晶温度是多少;影响PET结晶温度的因素有哪些?;预结晶单元的工作原理是什么?;搅拌式结晶干燥机的工作原理是什么?;搅拌式结晶干燥机的适用范围有哪些?;搅拌式结晶干燥机的维护保养指南;介绍一下预结晶器在PET切片拉丝干燥系统中的作用;高速注塑PET结晶干燥设备的工作原理是什么?;PET结晶干燥除湿系统;回收与原生PET加工结晶干燥除湿系统;PET专用260度分子筛深度除湿机工作原理;如何维护和保养PET Desiccant Drying分子筛除湿干燥机?;介绍一下双塔分子筛节能除湿机的工作原理;PET除湿干燥系统的优势;搅拌动态一体化干燥机和中央集中干燥系统哪个更适合大型生产?;动态干燥机的工作原理是什么?;纤维PET干燥系统;PET 拉丝干燥系统流程图;PET注塑瓶胚除湿干燥+组合除露机的工作原理是什么?;一套PET破碎料除湿干燥系统产量700KG/H ; 满足干燥料斗和挤出机的供料;常用的PET瓶胚生产前来料是不是已经结晶?;PET 瓶胚专用转轮式 VS 双塔式分子筛整套干燥系统。
Further reading on crystallizing and drying parameters, pilot lines and troubleshooting is linked above; each note is a technical article from the same workshop practice.
