产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

塑料除湿干燥机 青岛 TCD-600|Plastic Desiccant Dryer / Dehumidifying Dryer

日期:2026-11-20 07:29
浏览次数:3
摘要:青岛家电注塑与 PVC 管材集群,露点 -20~-25 ℃,料斗 60 kg。中英文对照说明结构与参数。

青岛塑料除湿干燥机 TCD-600

青岛塑料除湿干燥机 TCD-600|Plastic Desiccant Dryer TCD-600

适用于青岛的家电注塑与 PVC 管材集群。设备按料斗容积 60 kg、风量约 80 m³/h、露点 -20~-25 ℃ 的配置供货,可配机边或集中两种安装方式。

Built for the home-appliance injection and PVC pipe cluster in 青岛, supplied with a 60 kg hopper, about 80 m³/h airflow and a dew point of -20~-25 °C, for machine-side or central installation.

这一条重点讲:能耗与风量匹配

Focus of this page: A lower dew point is not always better; when airflow does not match hopper volume, power per ton rises

露点不是越低越好,风量与料斗容积不匹配时,单位产量的电耗会明显上升。在青岛一带的车间,风量与料斗容积要随机台吨位一起定。

A lower dew point is not always better; when airflow does not match hopper volume, power per ton rises. In workshops like those in 青岛, the airflow and hopper figure is set together with the machine tonnage.

结构与参数 / Structure and figures

蜂巢转轮除湿 + 电加热料斗 + 闭环风路;露点 -20~-25 ℃、料斗 60 kg、风量 80 m³/h、再生加热 120~160 ℃ 可调;料温上限按原料牌号设定,一般不超过 120 ℃。

Honeycomb wheel dehumidifying, electrical hopper heating and a closed-loop air path: dew point -20~-25 °C, hopper 60 kg, airflow 80 m³/h, regeneration 120-160 °C adjustable, material temperature normally kept under 120 °C.

接口为单相/三相可选,控制面板带露点显示与超温报警,料位不足时自动提示补料。

Single or three-phase supply, dew-point readout and over-temperature alarm on the panel, with a low-level refill prompt.

交货与调试:青岛及周边可上门安装调试,随机提供中文/英文操作说明与常见故障对照表。

Delivery: installation and commissioning are available in 青岛 and nearby areas, with Chinese/English manuals and a fault cross-reference table.

粤公网安备 44190002002288号