注塑瓶坯72腔模具除露机

注塑瓶坯72腔模具除露机,PET模具,模具除露机

下面给你 **72腔 PET 瓶坯模具除露机** 专用版 **设备介绍 + 工作原理 + 结构 + 技术参数（中英双语）** 可直接用于：标书、宣传册、PPT、外贸报价单。 --- # 72腔 PET 瓶坯模具除露机 ## 72-Cavity PET Preform Mold Dehumidifier

 ### 一、设备概述 / Overview **中文** 本设备专为 **72腔 PET 瓶坯高速注塑模具** 设计，用于解决低温冷却模具因车间温湿度差产生的**结露问题**。通过深度除湿、恒温加热、均匀分流和开模同步吹扫，彻底消除型腔、分型面、顶针区域凝露，提升瓶坯透明度与合格率，保护模具不生锈、不卡模，满足高速生产线连续稳定运行。

 **English** This equipment is specially designed for **72-cavity high-speed PET preform injection molds** to solve **condensation** on low-temperature cooling molds caused by temperature and humidity difference in the workshop. Through deep dehumidification, constant temperature heating, uniform air distribution and synchronous blowing with mold opening, it completely eliminates condensation on cavities, parting surfaces and ejector pins, improves preform transparency and qualification rate, protects molds from rust and jamming, and meets the requirements of continuous and stable operation of high-speed production lines. 

--- ### 二、工作原理 / Working Principle **中文** 1. 环境空气经**三级过滤**净化除尘。

 2. 通过**蜂巢转轮深度除湿**，获得露点 ≤-40℃ 的超干燥空气。

 3. 干燥空气**恒温加热至 40～60℃**，避免二次结露。

 4. 经**72腔专用分流系统**均匀分配风量。 

5. 与注塑机**开模同步吹扫**，吹干模具并形成气帘阻隔湿气。

 6. 转轮自动高温再生，实现24小时连续除湿。 **English** 1. Ambient air is purified by **3-stage filtration**. 2. Deeply dehumidified by **honeycomb rotor** to ultra-dry air with dew point ≤-40℃. 3. Dry air is **heated to 40~60℃** at constant temperature to avoid re-condensation. 4. Air is evenly distributed through **special air distribution system for 72 cavities**. 5. **Blows synchronously with mold opening** to dry the mold and form an isolation air curtain. 6. Rotor regenerates automatically for 24-hour continuous dehumidification. 

--- ### 三、结构组成 / Structure Composition **中文** 

1. 三级过滤系统（初效+中效+高效）

 2. 蜂巢转轮深度除湿系统

 3. 恒温加热与送风系统 

4. 72腔均匀分流系统 

5. 模具吹扫系统（72个型腔喷嘴 + 分型面气帘 + 顶针吹扫）

 6. PLC智能控制系统（触摸屏+联动+报警） **English** 1. 3-stage filtration system (G4+F8+H13) 2. Honeycomb rotor deep dehumidification system 3. Constant temperature heating & air supply system 4. 72-cavity uniform air distribution system 5. Mold blowing system (72 cavity nozzles + parting air curtain + pin blowing) 6. PLC intelligent control system (touch screen + linkage + alarm) --- ### 四、核心技术参数 / Key Technical Parameters 

**中文** - 适用模具：72腔 PET 瓶坯注塑模具 - 除湿方式：蜂巢转轮除湿 -

 露点温度：≤ -40℃ - 处理风量：600–900 m³/h - 出风温度：40–60℃ 恒温可调 - 吹扫配置：72个型腔喷嘴 + 分型面气帘 - 控制方式：PLC + 7寸触摸屏 -

 联动信号：注塑机开模/合模信号 - 电源：380V 50Hz 三相五线 - 整机功率：12–18 kW **English** - Suitable Mold: 72-cavity PET preform injection mold - Dehumidification: Honeycomb rotor - Dew Point: ≤ -40℃ - Air Flow: 600–900 m³/h - Outlet Temp.: 40–60℃ adjustable & constant - Blowing: 72 cavity nozzles + parting air curtain - Control: PLC + 7" touch screen - Linkage: Mold open/close signal - Power: 380V 50Hz 3-phase 5-wire - Power: 12–18 kW --- ### 五、主要特点 / Key Features 

**中文** - 专为72腔高速模具优化风量与分流 - 露点稳定≤-40℃，彻底杜绝凝露 - 与注塑机联动，不占用成型周期 - 72腔风量均匀，无死角、无局部结露 - 恒温出风，不影响模具冷却与瓶坯质量 - 超温、露点高、滤网堵塞自动报警 - 24小时连续稳定运行 **English** - Optimized air flow & distribution specially for 72-cavity high-speed molds - Stable dew point ≤-40℃, completely eliminate condensation - Linked with injection machine, no cycle time loss - Uniform air for 72 cavities, no dead zone - Constant temperature air, no influence on mold cooling & preform quality - Auto alarm for overheat, high dew point, filter clogging - 24h continuous & stable operation ---