产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

PET瓶胚注塑干燥系统 苏州 PDS-500|PET Preform Injection Drying System

日期:2026-11-19 10:55
浏览次数:0
摘要:苏州瓶胚车间用PET结晶除湿干燥系统,500 kg/h,露点 -40~-45 ℃。中英文对照。

苏州PET瓶胚注塑干燥系统 PDS-500

苏州PET瓶胚注塑干燥系统 PDS-500|PET Preform Injection Drying System PDS-500

面向苏州的片材、薄膜与医疗耗材集群。系统含预结晶段、除湿干燥段与机边输送段,按 500 kg/h 级瓶胚产量配置,干燥露点 -40~-45 ℃。

For the sheet, film and medical consumable cluster in 苏州: pre-crystallising, desiccant drying and machine-side conveying in one system, sized for about 500 kg/h of preforms with a drying dew point of -40~-45 °C.

这一条重点讲:瓶胚生产的水解风险

Focus of this page: Water in molten PET lowers molecular weight directly; under-dried preforms show stress whitening and burst bottles

PET 熔融时水分会直接引起分子量下降,干燥不到位的瓶胚会出现应力发白与爆瓶。苏州的瓶胚车间在换牌号与开停机阶段,这一段较容易出批量异常。

Water in molten PET lowers molecular weight directly; under-dried preforms show stress whitening and burst bottles. Preform shops in 苏州 hit this hardest when changing grade and at start-up or shutdown.

三段工艺与参数 / Three stages and figures

预结晶 150~170 ℃、搅拌防粘连;干燥 160~170 ℃、露点 -40~-45 ℃、停留 4~6 小时;成品含水控制在 50 ppm 以内,输送段保温密封。

Pre-crystallising at 150-170 °C with agitation against blocking; drying at 160-170 °C, dew point -40~-45 °C, 4-6 h residence; finished moisture kept under 50 ppm, conveying line insulated and sealed.

系统带露点、料温、料位三路显示,异常时报警而不是直接停机,便于值班人员判断。

Dew point, material temperature and level are all displayed; faults raise an alarm instead of an immediate stop, so the operator can judge.

交货与调试:苏州及周边可上门安装并带料试机,随机提供中英文工艺参数表。

Delivery: installation and trial runs with material are available in 苏州 and nearby, with a bilingual process parameter sheet.

粤公网安备 44190002002288号