产品中心
PRODUCT CENTER

  • 联系人 : 曹镜森先生
  • 联系电话 : 0769-82226193
  • 传真 : 0769-82226193
  • 移动电话 : 13925217478
  • 地址 : ** 广东省东莞市大朗镇仙村工业区
  • Email : caojingshen@126.com
  • 邮编 : 523792
  • 公司网址 : http://www.szdatian.net.cn
  • MSN : caoshingcer@126.com
  • QQ : 454992321
文章详情

塑料除湿干燥机 苏州 TCD-900|Plastic Desiccant Dryer / Dehumidifying Dryer

日期:2026-11-19 10:55
浏览次数:0
摘要:苏州片材、薄膜与医疗耗材集群,露点 -25~-30 ℃,料斗 90 kg。中英文对照说明结构与参数。

苏州塑料除湿干燥机 TCD-900

苏州塑料除湿干燥机 TCD-900|Plastic Desiccant Dryer TCD-900

适用于苏州的片材、薄膜与医疗耗材集群。设备按料斗容积 90 kg、风量约 120 m³/h、露点 -25~-30 ℃ 的配置供货,可配机边或集中两种安装方式。

Built for the sheet, film and medical consumable cluster in 苏州, supplied with a 90 kg hopper, about 120 m³/h airflow and a dew point of -25~-30 °C, for machine-side or central installation.

这一条重点讲:换料与残料清理

Focus of this page: Cutting the residue of the previous batch is the step that most often goes wrong when switching colour or grade

把上一批料的残留降到可接受范围,是切换颜色与牌号时容易出问题的一环。在苏州一带的车间,风量与料斗容积要随机台吨位一起定。

Cutting the residue of the previous batch is the step that most often goes wrong when switching colour or grade. In workshops like those in 苏州, the airflow and hopper figure is set together with the machine tonnage.

结构与参数 / Structure and figures

蜂巢转轮除湿 + 电加热料斗 + 闭环风路;露点 -25~-30 ℃、料斗 90 kg、风量 120 m³/h、再生加热 120~160 ℃ 可调;料温上限按原料牌号设定,一般不超过 120 ℃。

Honeycomb wheel dehumidifying, electrical hopper heating and a closed-loop air path: dew point -25~-30 °C, hopper 90 kg, airflow 120 m³/h, regeneration 120-160 °C adjustable, material temperature normally kept under 120 °C.

接口为单相/三相可选,控制面板带露点显示与超温报警,料位不足时自动提示补料。

Single or three-phase supply, dew-point readout and over-temperature alarm on the panel, with a low-level refill prompt.

交货与调试:苏州及周边可上门安装调试,随机提供中文/英文操作说明与常见故障对照表。

Delivery: installation and commissioning are available in 苏州 and nearby areas, with Chinese/English manuals and a fault cross-reference table.

粤公网安备 44190002002288号