产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 13925217478
- 地址 : ** 广东省东莞市大朗镇仙村工业区
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : http://www.szdatian.net.cn
- MSN : caoshingcer@126.com
- QQ : 454992321
杭州模温机 TMT-9
杭州模温机 TMT-9
Mold Temperature Controller TMT-9 for Hangzhou
杭州模温机 TMT-9(Mold Temperature Controller TMT-9):9 kW 加热配循环泵,水或油两用,模具温度按 ±1℃ 保持,成型周期与外观更稳。
Mold Temperature Controller TMT-9 for Hangzhou: A 9 kW heater with circulation pump, water or oil, holds mold temperature within plus or minus 1 C for steadier cycles and surfaces.
设备说明 / Equipment Overview
加热筒与循环泵一体,回水温度进控制器,PID 调加热功率;水式用于 90℃ 以下,油式到 200℃。
Heater barrel and pump are integrated, return temperature drives PID heating; water covers below 90 C and oil reaches 200 C.
结构与控制 / Structure & Control
管路一进一出接模具水路,带排气与压力表;超温、缺液、泵过载都有保护,报警后停机不再加热。
One in and one out connect to the mold circuit with vent and gauge; over-temperature, low level and pump overload all trip the heater.
运行与精度 / Performance & Accuracy
控温精度 ±1℃,大模具升温慢时先预热;多副模具共用一台时加分流,温差大的模具单独配机。
Accuracy holds at plus or minus 1 C; preheat large molds, split flow when several molds share one unit, and give very different molds their own unit.
操作与维护 / Operation & Maintenance
每月换水或换油并清过滤器,油式按运行小时换油;泵密封与加热管每季度检查,结垢会拉低换热。
Change water or oil monthly with filter cleaning, oil by running hours, and check pump seals and heater elements quarterly since scale cuts heat transfer.
参数速览 / Specifications
型号 TMT-9|加热 9 kW|较高 200℃(水/油两用)|精度 ±1℃|泵 0.37 kW
Model TMT-9 | 9 kW heater | Up to 200 C, water or oil | Accuracy plus or minus 1 C | 0.37 kW pump
应用场景 / Applications
精密注塑模温控制、薄壁件与外观件成型、挤出辊筒与压延辊温、试模与打样阶段快速升温。
Mold temperature control on precision molding, thin-wall and cosmetic parts, roll temperature on extrusion, and fast heat-up for trials.
杭州配套 / Local Support in Hangzhou
包装、日化与电子注塑为主,小批量多品种,换料快、清料省时是硬指标。
Packaging, personal care and electronics in small batches of many items, where fast changes and easy cleaning are essential.
选型与交付 / Sizing & Delivery
提供物料清单与产线节拍后出具选型计算书,确认配置与产能;签约后按约定交期发运,到场安装、联动调试与操作培训,随机附手册与备件清单。
Send the material list and takt time and we return a sizing sheet confirming configuration and capacity. After order we ship on the agreed date, install, commission and train, with manual and spare list.
常见问题 / FAQ
Q:水和油怎么选?
Q: Water or oil?
A:90℃ 以下用水,升温快、清洁;更高温度或长管路用油,注意油品氧化与更换周期。
Water below 90 C heats fast and stays clean; oil for higher temperatures or long circuits, watching oxidation and change intervals.
Q:模温不稳会影响什么?
Q: What does unstable mold temperature affect?
A:直接影响收缩率与外观:温度偏低易缺料与熔接痕,偏高则翘曲与周期拉长。先稳模温再调工艺。
Shrinkage and appearance directly: low temperature gives short shots and weld lines, high gives warpage and longer cycles. Stabilise mold temperature before tuning the process.
杭州 本地配套与选型提示 / Local Notes for 杭州
包装、化纤与电子配套并行,薄膜与片材线对色差敏感,色母组独立小螺杆,混料腔密闭。
Local industry sets the material mix in 杭州, so sizing follows the material mix and the regrind share rather than a fixed catalogue figure; the component count and weighing range are quoted against the actual job.
对应机型与配置见站内产品页:水式模温机。
Model and configuration: 水式模温机.
